Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Pull networking updates from David Miller:
 "More bug fixes, nothing gets past these guys"

 1) More kernel info leaks found by Mathias Krause, this time in the
    IPSEC configuration layers.

 2) When IPSEC policies change, we do not properly make sure that cached
    routes (which could now be stale) throughout the system will be
    revalidated.  Fix this by generalizing the generation count
    invalidation scheme used by ipv4.  From Nicolas Dichtel.

 3) When repairing TCP sockets, we need to allow to restore not just the
    send window scale, but the receive one too.  Extend the existing
    interface to achieve this in a backwards compatible way.  From
    Andrey Vagin.

 4) A fix for FCOE scatter gather feature validation erroneously caused
    scatter gather to be disabled for things like AOE too.  From Ed L
    Cashin.

 5) Several cases of mishandling of error pointers, from Mathias Krause,
    Wei Yongjun, and Devendra Naga.

 6) Fix gianfar build, from Richard Cochran.

 7) CAP_NET_* failures should return -EPERM not -EACCES, from Zhao
    Hongjiang.

 8) Hardware reset fix in janz-ican3 CAN driver, from Ira W Snyder.

 9) Fix oops during rmmod in ti_hecc CAN driver, from Marc Kleine-Budde.

10) The removal of the conditional compilation of the clk support code
    in the stmmac driver broke things.  This is because the interfaces
    used are the ones that don't also perform the enable/disable of the
    clk.  Fix from Stefan Roese.

11) The QFQ packet scheduler can record out of range virtual start
    times, resulting later in misbehavior and even crashes.  Fix from
    Paolo Valente.

12) If MSG_WAITALL is used with IOAT DMA under TCP, we can wedge the
    receiver when the advertised receive window goes to zero.  Detect
    this case and force the processing of the IOAT DMA queue when it
    happens to avoid getting stuck.  Fix from Michal Kubecek.

13) batman-adv assumes that test_bit() returns only 0 or 1, but this is
    not true for x86 (which returns -1 or 0, via the 'sbb' instruction).
    Fix from Linus Lussing.

14) Fix small packet corruption in e1000, from Tushar Dave.

15) make_blackhole() in the IPSEC policy code can do one read unlock too
    many, fix from Li RongQing.

16) The new tcp_try_coalesce() code introduced a bug in TCP URG
    handling, fix from Eric Dumazet.

17) Fix memory leak in __netif_receive_skb() when doing zerocopy and
    when hit an OOM condition.  From Michael S Tsirkin.

18) netxen blindly deferences pdev->bus->self, which is not guarenteed
    to be non-NULL.  Fix from Nikolay Aleksandrov.

19) Fix a performance regression caused by mistakes in ipv6 checksum
    validation in the bnx2x driver, fix from Michal Schmidt.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
  net/stmmac: Use clk_prepare_enable and clk_disable_unprepare
  net: change return values from -EACCES to -EPERM
  net/irda: sh_sir: fix return value check in sh_sir_set_baudrate()
  stmmac: fix return value check in stmmac_open_ext_timer()
  gianfar: fix phc index build failure
  ipv6: fix return value check in fib6_add()
  bnx2x: remove false warning regarding interrupt number
  can: ti_hecc: fix oops during rmmod
  can: janz-ican3: fix support for older hardware revisions
  net: do not disable sg for packets requiring no checksum
  aoe: assert AoE packets marked as requiring no checksum
  at91ether: return PTR_ERR if call to clk_get fails
  xfrm_user: don't copy esn replay window twice for new states
  xfrm_user: ensure user supplied esn replay window is valid
  xfrm_user: fix info leak in copy_to_user_tmpl()
  xfrm_user: fix info leak in copy_to_user_policy()
  xfrm_user: fix info leak in copy_to_user_state()
  xfrm_user: fix info leak in copy_to_user_auth()
  net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200
  tcp: restore rcv_wscale in a repair mode (v2)
  ...

drivers/block/aoe/aoecmd.c

@@ -35,6 +35,7 @@ new_skb(ulong len)
 		skb_reset_mac_header(skb);
 		skb_reset_network_header(skb);
 		skb->protocol = __constant_htons(ETH_P_AOE);
+		skb_checksum_none_assert(skb);
 	}
 	return skb;
 }

drivers/net/can/janz-ican3.c

@@ -1391,7 +1391,6 @@ static irqreturn_t ican3_irq(int irq, void *dev_id)
  */
 static int ican3_reset_module(struct ican3_dev *mod)
 {
-	u8 val = 1 << mod->num;
 	unsigned long start;
 	u8 runold, runnew;
 
@@ -1405,8 +1404,7 @@ static int ican3_reset_module(struct ican3_dev *mod)
 	runold = ioread8(mod->dpm + TARGET_RUNNING);
 
 	/* reset the module */
-	iowrite8(val, &mod->ctrl->reset_assert);
-	iowrite8(val, &mod->ctrl->reset_deassert);
+	iowrite8(0x00, &mod->dpmctrl->hwreset);
 
 	/* wait until the module has finished resetting and is running */
 	start = jiffies;

drivers/net/can/ti_hecc.c

@@ -984,12 +984,12 @@ static int __devexit ti_hecc_remove(struct platform_device *pdev)
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct ti_hecc_priv *priv = netdev_priv(ndev);
 
+	unregister_candev(ndev);
 	clk_disable(priv->clk);
 	clk_put(priv->clk);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	iounmap(priv->base);
 	release_mem_region(res->start, resource_size(res));
-	unregister_candev(ndev);
 	free_candev(ndev);
 	platform_set_drvdata(pdev, NULL);
 

drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c

@@ -662,14 +662,16 @@ void bnx2x_csum_validate(struct sk_buff *skb, union eth_rx_cqe *cqe,
 				 struct bnx2x_fastpath *fp,
 				 struct bnx2x_eth_q_stats *qstats)
 {
-	/* Do nothing if no IP/L4 csum validation was done */
-
+	/* Do nothing if no L4 csum validation was done.
+	 * We do not check whether IP csum was validated. For IPv4 we assume
+	 * that if the card got as far as validating the L4 csum, it also
+	 * validated the IP csum. IPv6 has no IP csum.
+	 */
 	if (cqe->fast_path_cqe.status_flags &
-	    (ETH_FAST_PATH_RX_CQE_IP_XSUM_NO_VALIDATION_FLG |
-	     ETH_FAST_PATH_RX_CQE_L4_XSUM_NO_VALIDATION_FLG))
+	    ETH_FAST_PATH_RX_CQE_L4_XSUM_NO_VALIDATION_FLG)
 		return;
 
-	/* If both IP/L4 validation were done, check if an error was found. */
+	/* If L4 validation was done, check if an error was found. */
 
 	if (cqe->fast_path_cqe.type_error_flags &
 	    (ETH_FAST_PATH_RX_CQE_IP_BAD_XSUM_FLG |

drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c

@@ -9831,12 +9831,13 @@ static void __devinit bnx2x_get_igu_cam_info(struct bnx2x *bp)
 	}
 
 #ifdef CONFIG_PCI_MSI
-	/*
-	 * It's expected that number of CAM entries for this functions is equal
-	 * to the number evaluated based on the MSI-X table size. We want a
-	 * harsh warning if these values are different!
+	/* Due to new PF resource allocation by MFW T7.4 and above, it's
+	 * optional that number of CAM entries will not be equal to the value
+	 * advertised in PCI.
+	 * Driver should use the minimal value of both as the actual status
+	 * block count
 	 */
-	WARN_ON(bp->igu_sb_cnt != igu_sb_cnt);
+	bp->igu_sb_cnt = min_t(int, bp->igu_sb_cnt, igu_sb_cnt);
 #endif
 
 	if (igu_sb_cnt == 0)

drivers/net/ethernet/cadence/at91_ether.c

@@ -1086,7 +1086,7 @@ static int __init at91ether_probe(struct platform_device *pdev)
 	/* Clock */
 	lp->ether_clk = clk_get(&pdev->dev, "ether_clk");
 	if (IS_ERR(lp->ether_clk)) {
-		res = -ENODEV;
+		res = PTR_ERR(lp->ether_clk);
 		goto err_ioumap;
 	}
 	clk_enable(lp->ether_clk);

drivers/net/ethernet/freescale/gianfar_ethtool.c

@@ -1773,6 +1773,7 @@ static int gfar_get_nfc(struct net_device *dev, struct ethtool_rxnfc *cmd,
 }
 
 int gfar_phc_index = -1;
+EXPORT_SYMBOL(gfar_phc_index);
 
 static int gfar_get_ts_info(struct net_device *dev,
 			    struct ethtool_ts_info *info)

drivers/net/ethernet/freescale/gianfar_ptp.c

@@ -515,7 +515,7 @@ static int gianfar_ptp_probe(struct platform_device *dev)
 		err = PTR_ERR(etsects->clock);
 		goto no_clock;
 	}
-	gfar_phc_clock = ptp_clock_index(etsects->clock);
+	gfar_phc_index = ptp_clock_index(etsects->clock);
 
 	dev_set_drvdata(&dev->dev, etsects);
 
@@ -539,7 +539,7 @@ static int gianfar_ptp_remove(struct platform_device *dev)
 	gfar_write(&etsects->regs->tmr_temask, 0);
 	gfar_write(&etsects->regs->tmr_ctrl,   0);
 
-	gfar_phc_clock = -1;
+	gfar_phc_index = -1;
 	ptp_clock_unregister(etsects->clock);
 	iounmap(etsects->regs);
 	release_resource(etsects->rsrc);

drivers/net/ethernet/intel/e1000/e1000_main.c

@@ -3149,6 +3149,17 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
 		return NETDEV_TX_OK;
 	}
 
+	/* On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
+	 * packets may get corrupted during padding by HW.
+	 * To WA this issue, pad all small packets manually.
+	 */
+	if (skb->len < ETH_ZLEN) {
+		if (skb_pad(skb, ETH_ZLEN - skb->len))
+			return NETDEV_TX_OK;
+		skb->len = ETH_ZLEN;
+		skb_set_tail_pointer(skb, ETH_ZLEN);
+	}
+
 	mss = skb_shinfo(skb)->gso_size;
 	/* The controller does a simple calculation to
 	 * make sure there is enough room in the FIFO before

drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c

@@ -1378,6 +1378,10 @@ static void netxen_mask_aer_correctable(struct netxen_adapter *adapter)
 	struct pci_dev *root = pdev->bus->self;
 	u32 aer_pos;
 
+	/* root bus? */
+	if (!root)
+		return;
+
 	if (adapter->ahw.board_type != NETXEN_BRDTYPE_P3_4_GB_MM &&
 		adapter->ahw.board_type != NETXEN_BRDTYPE_P3_10G_TP)
 		return;

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -1066,7 +1066,7 @@ static int stmmac_open(struct net_device *dev)
 	} else
 		priv->tm->enable = 1;
 #endif
-	clk_enable(priv->stmmac_clk);
+	clk_prepare_enable(priv->stmmac_clk);
 
 	stmmac_check_ether_addr(priv);
 
@@ -1188,7 +1188,7 @@ static int stmmac_open(struct net_device *dev)
 	if (priv->phydev)
 		phy_disconnect(priv->phydev);
 
-	clk_disable(priv->stmmac_clk);
+	clk_disable_unprepare(priv->stmmac_clk);
 
 	return ret;
 }
@@ -1246,7 +1246,7 @@ static int stmmac_release(struct net_device *dev)
 #ifdef CONFIG_STMMAC_DEBUG_FS
 	stmmac_exit_fs();
 #endif
-	clk_disable(priv->stmmac_clk);
+	clk_disable_unprepare(priv->stmmac_clk);
 
 	return 0;
 }
@@ -2178,7 +2178,7 @@ int stmmac_suspend(struct net_device *ndev)
 	else {
 		stmmac_set_mac(priv->ioaddr, false);
 		/* Disable clock in case of PWM is off */
-		clk_disable(priv->stmmac_clk);
+		clk_disable_unprepare(priv->stmmac_clk);
 	}
 	spin_unlock_irqrestore(&priv->lock, flags);
 	return 0;
@@ -2203,7 +2203,7 @@ int stmmac_resume(struct net_device *ndev)
 		priv->hw->mac->pmt(priv->ioaddr, 0);
 	else
 		/* enable the clk prevously disabled */
-		clk_enable(priv->stmmac_clk);
+		clk_prepare_enable(priv->stmmac_clk);
 
 	netif_device_attach(ndev);
 

drivers/net/ethernet/stmicro/stmmac/stmmac_timer.c

@@ -97,19 +97,19 @@ static struct clk *timer_clock;
 static void stmmac_tmu_start(unsigned int new_freq)
 {
 	clk_set_rate(timer_clock, new_freq);
-	clk_enable(timer_clock);
+	clk_prepare_enable(timer_clock);
 }
 
 static void stmmac_tmu_stop(void)
 {
-	clk_disable(timer_clock);
+	clk_disable_unprepare(timer_clock);
 }
 
 int stmmac_open_ext_timer(struct net_device *dev, struct stmmac_timer *tm)
 {
 	timer_clock = clk_get(NULL, TMU_CHANNEL);
 
-	if (timer_clock == NULL)
+	if (IS_ERR(timer_clock))
 		return -1;
 
 	if (tmu2_register_user(stmmac_timer_handler, (void *)dev) < 0) {
@@ -126,7 +126,7 @@ int stmmac_open_ext_timer(struct net_device *dev, struct stmmac_timer *tm)
 
 int stmmac_close_ext_timer(void)
 {
-	clk_disable(timer_clock);
+	clk_disable_unprepare(timer_clock);
 	tmu2_unregister_user();
 	clk_put(timer_clock);
 	return 0;

drivers/net/irda/sh_sir.c

@@ -280,7 +280,7 @@ static int sh_sir_set_baudrate(struct sh_sir_self *self, u32 baudrate)
 	}
 
 	clk = clk_get(NULL, "irda_clk");
-	if (!clk) {
+	if (IS_ERR(clk)) {
 		dev_err(dev, "can not get irda_clk\n");
 		return -EIO;
 	}

drivers/net/usb/asix_devices.c

@@ -961,6 +961,10 @@ static const struct usb_device_id	products [] = {
 	// DLink DUB-E100 H/W Ver B1 Alternate
 	USB_DEVICE (0x2001, 0x3c05),
 	.driver_info = (unsigned long) &ax88772_info,
+}, {
+       // DLink DUB-E100 H/W Ver C1
+       USB_DEVICE (0x2001, 0x1a02),
+       .driver_info = (unsigned long) &ax88772_info,
 }, {
 	// Linksys USB1000
 	USB_DEVICE (0x1737, 0x0039),

drivers/net/usb/qmi_wwan.c

@@ -366,23 +366,28 @@ static const struct usb_device_id products[] = {
 	},
 
 	/* 2. Combined interface devices matching on class+protocol */
+	{	/* Huawei E367 and possibly others in "Windows mode" */
+		USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 7),
+		.driver_info        = (unsigned long)&qmi_wwan_info,
+	},
 	{	/* Huawei E392, E398 and possibly others in "Windows mode" */
 		USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 17),
 		.driver_info        = (unsigned long)&qmi_wwan_shared,
 	},
-	{	/* Pantech UML290 */
-		USB_DEVICE_AND_INTERFACE_INFO(0x106c, 0x3718, USB_CLASS_VENDOR_SPEC, 0xf0, 0xff),
+	{	/* Pantech UML290, P4200 and more */
+		USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf0, 0xff),
 		.driver_info        = (unsigned long)&qmi_wwan_shared,
 	},
 	{	/* Pantech UML290 - newer firmware */
-		USB_DEVICE_AND_INTERFACE_INFO(0x106c, 0x3718, USB_CLASS_VENDOR_SPEC, 0xf1, 0xff),
+		USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf1, 0xff),
 		.driver_info        = (unsigned long)&qmi_wwan_shared,
 	},
 
 	/* 3. Combined interface devices matching on interface number */
 	{QMI_FIXED_INTF(0x19d2, 0x0055, 1)},	/* ZTE (Vodafone) K3520-Z */
 	{QMI_FIXED_INTF(0x19d2, 0x0063, 4)},	/* ZTE (Vodafone) K3565-Z */
 	{QMI_FIXED_INTF(0x19d2, 0x0104, 4)},	/* ZTE (Vodafone) K4505-Z */
+	{QMI_FIXED_INTF(0x19d2, 0x0157, 5)},	/* ZTE MF683 */
 	{QMI_FIXED_INTF(0x19d2, 0x0167, 4)},	/* ZTE MF820D */
 	{QMI_FIXED_INTF(0x19d2, 0x0326, 4)},	/* ZTE MF821D */
 	{QMI_FIXED_INTF(0x19d2, 0x1008, 4)},	/* ZTE (Vodafone) K3570-Z */

drivers/net/wireless/ath/ath9k/ar9003_eeprom.c

@@ -2982,6 +2982,10 @@ static u32 ath9k_hw_ar9300_get_eeprom(struct ath_hw *ah,
 	case EEP_RX_MASK:
 		return pBase->txrxMask & 0xf;
 	case EEP_PAPRD:
+		if (AR_SREV_9462(ah))
+			return false;
+		if (!ah->config.enable_paprd);
+			return false;
 		return !!(pBase->featureEnable & BIT(5));
 	case EEP_CHAIN_MASK_REDUCE:
 		return (pBase->miscConfiguration >> 0x3) & 0x1;

drivers/net/wireless/ath/ath9k/debug.c

@@ -1577,6 +1577,8 @@ int ath9k_init_debug(struct ath_hw *ah)
 			    sc->debug.debugfs_phy, sc, &fops_tx_chainmask);
 	debugfs_create_file("disable_ani", S_IRUSR | S_IWUSR,
 			    sc->debug.debugfs_phy, sc, &fops_disable_ani);
+	debugfs_create_bool("paprd", S_IRUSR | S_IWUSR, sc->debug.debugfs_phy,
+			    &sc->sc_ah->config.enable_paprd);
 	debugfs_create_file("regidx", S_IRUSR | S_IWUSR, sc->debug.debugfs_phy,
 			    sc, &fops_regidx);
 	debugfs_create_file("regval", S_IRUSR | S_IWUSR, sc->debug.debugfs_phy,

drivers/net/wireless/ath/ath9k/hw.c

@@ -2497,10 +2497,6 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
 		pCap->rx_status_len = sizeof(struct ar9003_rxs);
 		pCap->tx_desc_len = sizeof(struct ar9003_txc);
 		pCap->txs_len = sizeof(struct ar9003_txs);
-		if (!ah->config.paprd_disable &&
-		    ah->eep_ops->get_eeprom(ah, EEP_PAPRD) &&
-		    !AR_SREV_9462(ah))
-			pCap->hw_caps |= ATH9K_HW_CAP_PAPRD;
 	} else {
 		pCap->tx_desc_len = sizeof(struct ath_desc);
 		if (AR_SREV_9280_20(ah))

drivers/net/wireless/ath/ath9k/hw.h

@@ -236,7 +236,6 @@ enum ath9k_hw_caps {
 	ATH9K_HW_CAP_LDPC			= BIT(6),
 	ATH9K_HW_CAP_FASTCLOCK			= BIT(7),
 	ATH9K_HW_CAP_SGI_20			= BIT(8),
-	ATH9K_HW_CAP_PAPRD			= BIT(9),
 	ATH9K_HW_CAP_ANT_DIV_COMB		= BIT(10),
 	ATH9K_HW_CAP_2GHZ			= BIT(11),
 	ATH9K_HW_CAP_5GHZ			= BIT(12),
@@ -287,12 +286,12 @@ struct ath9k_ops_config {
 	u8 pcie_clock_req;
 	u32 pcie_waen;
 	u8 analog_shiftreg;
-	u8 paprd_disable;
 	u32 ofdm_trig_low;
 	u32 ofdm_trig_high;
 	u32 cck_trig_high;
 	u32 cck_trig_low;
 	u32 enable_ani;
+	u32 enable_paprd;
 	int serialize_regmode;
 	bool rx_intr_mitigation;
 	bool tx_intr_mitigation;

drivers/net/wireless/ath/ath9k/link.c

@@ -423,7 +423,7 @@ void ath_ani_calibrate(unsigned long data)
 		cal_interval = min(cal_interval, (u32)short_cal_interval);
 
 	mod_timer(&common->ani.timer, jiffies + msecs_to_jiffies(cal_interval));
-	if ((sc->sc_ah->caps.hw_caps & ATH9K_HW_CAP_PAPRD) && ah->caldata) {
+	if (ah->eep_ops->get_eeprom(ah, EEP_PAPRD) && ah->caldata) {
 		if (!ah->caldata->paprd_done)
 			ieee80211_queue_work(sc->hw, &sc->paprd_work);
 		else if (!ah->paprd_table_write_done)

drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.c

@@ -638,6 +638,8 @@ static int brcmf_sdio_pd_probe(struct platform_device *pdev)
 
 		oobirq_entry = kzalloc(sizeof(struct brcmf_sdio_oobirq),
 				       GFP_KERNEL);
+		if (!oobirq_entry)
+			return -ENOMEM;
 		oobirq_entry->irq = res->start;
 		oobirq_entry->flags = res->flags & IRQF_TRIGGER_MASK;
 		list_add_tail(&oobirq_entry->list, &oobirq_lh);