Merge branch 'master' of /home/trondmy/kernel/linux-2.6/

Documentation/i2c/busses/i2c-i801

@@ -48,14 +48,9 @@ following:
 The SMBus controller is function 3 in device 1f. Class 0c05 is SMBus Serial
 Controller.
 
-If you do NOT see the 24x3 device at function 3, and you can't figure out
-any way in the BIOS to enable it,
-
 The ICH chips are quite similar to Intel's PIIX4 chip, at least in the
 SMBus controller.
 
-See the file i2c-piix4 for some additional information.
-
 
 Process Call Support
 --------------------
@@ -74,6 +69,61 @@ SMBus 2.0 Support
 
 The 82801DB (ICH4) and later chips support several SMBus 2.0 features.
 
+
+Hidden ICH SMBus
+----------------
+
+If your system has an Intel ICH south bridge, but you do NOT see the
+SMBus device at 00:1f.3 in lspci, and you can't figure out any way in the
+BIOS to enable it, it means it has been hidden by the BIOS code. Asus is
+well known for first doing this on their P4B motherboard, and many other
+boards after that. Some vendor machines are affected as well.
+
+The first thing to try is the "i2c_ec" ACPI driver. It could be that the
+SMBus was hidden on purpose because it'll be driven by ACPI. If the
+i2c_ec driver works for you, just forget about the i2c-i801 driver and
+don't try to unhide the ICH SMBus. Even if i2c_ec doesn't work, you
+better make sure that the SMBus isn't used by the ACPI code. Try loading
+the "fan" and "thermal" drivers, and check in /proc/acpi/fan and
+/proc/acpi/thermal_zone. If you find anything there, it's likely that
+the ACPI is accessing the SMBus and it's safer not to unhide it. Only
+once you are certain that ACPI isn't using the SMBus, you can attempt
+to unhide it.
+
+In order to unhide the SMBus, we need to change the value of a PCI
+register before the kernel enumerates the PCI devices. This is done in
+drivers/pci/quirks.c, where all affected boards must be listed (see
+function asus_hides_smbus_hostbridge.) If the SMBus device is missing,
+and you think there's something interesting on the SMBus (e.g. a
+hardware monitoring chip), you need to add your board to the list.
+
+The motherboard is identified using the subvendor and subdevice IDs of the
+host bridge PCI device. Get yours with "lspci -n -v -s 00:00.0":
+
+00:00.0 Class 0600: 8086:2570 (rev 02)
+        Subsystem: 1043:80f2
+        Flags: bus master, fast devsel, latency 0
+        Memory at fc000000 (32-bit, prefetchable) [size=32M]
+        Capabilities: [e4] #09 [2106]
+        Capabilities: [a0] AGP version 3.0
+
+Here the host bridge ID is 2570 (82865G/PE/P), the subvendor ID is 1043
+(Asus) and the subdevice ID is 80f2 (P4P800-X). You can find the symbolic
+names for the bridge ID and the subvendor ID in include/linux/pci_ids.h,
+and then add a case for your subdevice ID at the right place in
+drivers/pci/quirks.c. Then please give it very good testing, to make sure
+that the unhidden SMBus doesn't conflict with e.g. ACPI.
+
+If it works, proves useful (i.e. there are usable chips on the SMBus)
+and seems safe, please submit a patch for inclusion into the kernel.
+
+Note: There's a useful script in lm_sensors 2.10.2 and later, named
+unhide_ICH_SMBus (in prog/hotplug), which uses the fakephp driver to
+temporarily unhide the SMBus without having to patch and recompile your
+kernel. It's very convenient if you just want to check if there's
+anything interesting on your hidden ICH SMBus.
+
+
 **********************
 The lm_sensors project gratefully acknowledges the support of Texas
 Instruments in the initial development of this driver.

Documentation/i2c/busses/i2c-parport

@@ -19,6 +19,7 @@ It currently supports the following devices:
  * (type=4) Analog Devices ADM1032 evaluation board
  * (type=5) Analog Devices evaluation boards: ADM1025, ADM1030, ADM1031
  * (type=6) Barco LPT->DVI (K5800236) adapter
+ * (type=7) One For All JP1 parallel port adapter
 
 These devices use different pinout configurations, so you have to tell
 the driver what you have, using the type module parameter. There is no
@@ -157,3 +158,17 @@ many more, using /dev/velleman.
   http://home.wanadoo.nl/hihihi/libk8005.htm
   http://struyve.mine.nu:8080/index.php?block=k8000
   http://sourceforge.net/projects/libk8005/
+
+
+One For All JP1 parallel port adapter
+-------------------------------------
+
+The JP1 project revolves around a set of remote controls which expose
+the I2C bus their internal configuration EEPROM lives on via a 6 pin
+jumper in the battery compartment. More details can be found at:
+
+http://www.hifi-remote.com/jp1/
+
+Details of the simple parallel port hardware can be found at:
+
+http://www.hifi-remote.com/jp1/hardware.shtml

Documentation/i2c/busses/i2c-piix4

@@ -6,7 +6,7 @@ Supported adapters:
     Datasheet: Publicly available at the Intel website
   * ServerWorks OSB4, CSB5, CSB6 and HT-1000 southbridges
     Datasheet: Only available via NDA from ServerWorks
-  * ATI IXP southbridges IXP200, IXP300, IXP400
+  * ATI IXP200, IXP300, IXP400 and SB600 southbridges
     Datasheet: Not publicly available
   * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge
     Datasheet: Publicly available at the SMSC website http://www.smsc.com

Documentation/i2c/busses/i2c-viapro

@@ -13,6 +13,9 @@ Supported adapters:
   * VIA Technologies, Inc. VT8235, VT8237R, VT8237A, VT8251
     Datasheet: available on request and under NDA from VIA
 
+  * VIA Technologies, Inc. CX700
+    Datasheet: available on request and under NDA from VIA
+
 Authors:
 	Ky�sti M�lkki <kmalkki@cc.hut.fi>,
 	Mark D. Studebaker <mdsxyz123@yahoo.com>,
@@ -44,10 +47,14 @@ Your lspci -n listing must show one of these :
  device 1106:3227   (VT8237R)
  device 1106:3337   (VT8237A)
  device 1106:3287   (VT8251)
+ device 1106:8324   (CX700)
 
 If none of these show up, you should look in the BIOS for settings like
 enable ACPI / SMBus or even USB.
 
 Except for the oldest chips (VT82C596A/B, VT82C686A and most probably
 VT8231), this driver supports I2C block transactions. Such transactions
 are mainly useful to read from and write to EEPROMs.
+
+The CX700 additionally appears to support SMBus PEC, although this driver
+doesn't implement it yet.

Documentation/i2c/porting-clients

@@ -129,6 +129,12 @@ Technical changes:
   structure, those name member should be initialized to a driver name
   string. i2c_driver itself has no name member anymore.
 
+* [Driver model] Instead of shutdown or reboot notifiers, provide a
+  shutdown() method in your driver.
+
+* [Power management] Use the driver model suspend() and resume()
+  callbacks instead of the obsolete pm_register() calls.
+
 Coding policy:
 
 * [Copyright] Use (C), not (c), for copyright.

Documentation/i2c/smbus-protocol

@@ -97,7 +97,7 @@ SMBus Write Word Data
 =====================
 
 This is the opposite operation of the Read Word Data command. 16 bits
-of data is read from a device, from a designated register that is 
+of data is written to a device, to the designated register that is
 specified through the Comm byte. 
 
 S Addr Wr [A] Comm [A] DataLow [A] DataHigh [A] P

Documentation/i2c/writing-clients

@@ -21,20 +21,26 @@ The driver structure
 
 Usually, you will implement a single driver structure, and instantiate
 all clients from it. Remember, a driver structure contains general access 
-routines, a client structure specific information like the actual I2C
-address.
+routines, and should be zero-initialized except for fields with data you
+provide.  A client structure holds device-specific information like the
+driver model device node, and its I2C address.
 
 static struct i2c_driver foo_driver = {
 	.driver = {
 		.name	= "foo",
 	},
-	.attach_adapter	= &foo_attach_adapter,
-	.detach_client	= &foo_detach_client,
-	.command	= &foo_command /* may be NULL */
+	.attach_adapter	= foo_attach_adapter,
+	.detach_client	= foo_detach_client,
+	.shutdown	= foo_shutdown,	/* optional */
+	.suspend	= foo_suspend,	/* optional */
+	.resume		= foo_resume,	/* optional */
+	.command	= foo_command,	/* optional */
 }
 
-The name field must match the driver name, including the case. It must not
-contain spaces, and may be up to 31 characters long.
+The name field is the driver name, and must not contain spaces.  It
+should match the module name (if the driver can be compiled as a module),
+although you can use MODULE_ALIAS (passing "foo" in this example) to add
+another name for the module.
 
 All other fields are for call-back functions which will be explained 
 below.
@@ -43,11 +49,18 @@ below.
 Extra client data
 =================
 
-The client structure has a special `data' field that can point to any
-structure at all. You can use this to keep client-specific data. You
+Each client structure has a special `data' field that can point to any
+structure at all.  You should use this to keep device-specific data,
+especially in drivers that handle multiple I2C or SMBUS devices.  You
 do not always need this, but especially for `sensors' drivers, it can
 be very useful.
 
+	/* store the value */
+	void i2c_set_clientdata(struct i2c_client *client, void *data);
+
+	/* retrieve the value */
+	void *i2c_get_clientdata(struct i2c_client *client);
+
 An example structure is below.
 
   struct foo_data {
@@ -493,6 +506,33 @@ by `__init_data'.  Hose functions and structures can be removed after
 kernel booting (or module loading) is completed.
 
 
+Power Management
+================
+
+If your I2C device needs special handling when entering a system low
+power state -- like putting a transceiver into a low power mode, or
+activating a system wakeup mechanism -- do that in the suspend() method.
+The resume() method should reverse what the suspend() method does.
+
+These are standard driver model calls, and they work just like they
+would for any other driver stack.  The calls can sleep, and can use
+I2C messaging to the device being suspended or resumed (since their
+parent I2C adapter is active when these calls are issued, and IRQs
+are still enabled).
+
+
+System Shutdown
+===============
+
+If your I2C device needs special handling when the system shuts down
+or reboots (including kexec) -- like turning something off -- use a
+shutdown() method.
+
+Again, this is a standard driver model call, working just like it
+would for any other driver stack:  the calls can sleep, and can use
+I2C messaging.
+
+
 Command function
 ================
 

Documentation/powerpc/booting-without-of.txt

@@ -1334,6 +1334,9 @@ platforms are moved over to use the flattened-device-tree model.
       fsl-usb2-mph compatible controllers.  Either this property or
       "port0" (or both) must be defined for "fsl-usb2-mph" compatible 
       controllers.
+    - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
+      controllers.  Can be "host", "peripheral", or "otg".  Default to
+      "host" if not defined for backward compatibility.
 
    Recommended properties :
     - interrupts : <a b> where a is the interrupt number and b is a
@@ -1367,6 +1370,7 @@ platforms are moved over to use the flattened-device-tree model.
 		#size-cells = <0>;
 		interrupt-parent = <700>;
 		interrupts = <26 1>;
+		dr_mode = "otg";
 		phy = "ulpi";
 	};