PM: EM: convert power field to micro-Watts precision and align drivers

The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.

Update all EM users which access 'power' field and assume the value is
in milli-Watts.

Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.

Example calculation which shows the rounding error and impact:

power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz

power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18

power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21

max_freq = 2000MHz

cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000

cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203

The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.

Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

drivers/cpufreq/mediatek-cpufreq-hw.c

@@ -51,7 +51,7 @@ static const u16 cpufreq_mtk_offsets[REG_ARRAY_SIZE] = {
 };
 
 static int __maybe_unused
-mtk_cpufreq_get_cpu_power(struct device *cpu_dev, unsigned long *mW,
+mtk_cpufreq_get_cpu_power(struct device *cpu_dev, unsigned long *uW,
 			  unsigned long *KHz)
 {
 	struct mtk_cpufreq_data *data;
@@ -71,8 +71,9 @@ mtk_cpufreq_get_cpu_power(struct device *cpu_dev, unsigned long *mW,
 	i--;
 
 	*KHz = data->table[i].frequency;
-	*mW = readl_relaxed(data->reg_bases[REG_EM_POWER_TBL] +
-			    i * LUT_ROW_SIZE) / 1000;
+	/* Provide micro-Watts value to the Energy Model */
+	*uW = readl_relaxed(data->reg_bases[REG_EM_POWER_TBL] +
+			    i * LUT_ROW_SIZE);
 
 	return 0;
 }

drivers/cpufreq/scmi-cpufreq.c

@@ -19,6 +19,7 @@
 #include <linux/slab.h>
 #include <linux/scmi_protocol.h>
 #include <linux/types.h>
+#include <linux/units.h>
 
 struct scmi_data {
 	int domain_id;
@@ -99,6 +100,7 @@ static int __maybe_unused
 scmi_get_cpu_power(struct device *cpu_dev, unsigned long *power,
 		   unsigned long *KHz)
 {
+	bool power_scale_mw = perf_ops->power_scale_mw_get(ph);
 	unsigned long Hz;
 	int ret, domain;
 
@@ -112,6 +114,10 @@ scmi_get_cpu_power(struct device *cpu_dev, unsigned long *power,
 	if (ret)
 		return ret;
 
+	/* Provide bigger resolution power to the Energy Model */
+	if (power_scale_mw)
+		*power *= MICROWATT_PER_MILLIWATT;
+
 	/* The EM framework specifies the frequency in KHz. */
 	*KHz = Hz / 1000;
 

drivers/opp/of.c

@@ -1443,12 +1443,12 @@ EXPORT_SYMBOL_GPL(dev_pm_opp_get_of_node);
  * It provides the power used by @dev at @kHz if it is the frequency of an
  * existing OPP, or at the frequency of the first OPP above @kHz otherwise
  * (see dev_pm_opp_find_freq_ceil()). This function updates @kHz to the ceiled
- * frequency and @mW to the associated power.
+ * frequency and @uW to the associated power.
  *
  * Returns 0 on success or a proper -EINVAL value in case of error.
  */
 static int __maybe_unused
-_get_dt_power(struct device *dev, unsigned long *mW, unsigned long *kHz)
+_get_dt_power(struct device *dev, unsigned long *uW, unsigned long *kHz)
 {
 	struct dev_pm_opp *opp;
 	unsigned long opp_freq, opp_power;
@@ -1465,7 +1465,7 @@ _get_dt_power(struct device *dev, unsigned long *mW, unsigned long *kHz)
 		return -EINVAL;
 
 	*kHz = opp_freq / 1000;
-	*mW = opp_power / 1000;
+	*uW = opp_power;
 
 	return 0;
 }
@@ -1475,14 +1475,14 @@ _get_dt_power(struct device *dev, unsigned long *mW, unsigned long *kHz)
  * This computes the power estimated by @dev at @kHz if it is the frequency
  * of an existing OPP, or at the frequency of the first OPP above @kHz otherwise
  * (see dev_pm_opp_find_freq_ceil()). This function updates @kHz to the ceiled
- * frequency and @mW to the associated power. The power is estimated as
+ * frequency and @uW to the associated power. The power is estimated as
  * P = C * V^2 * f with C being the device's capacitance and V and f
  * respectively the voltage and frequency of the OPP.
  *
  * Returns -EINVAL if the power calculation failed because of missing
  * parameters, 0 otherwise.
  */
-static int __maybe_unused _get_power(struct device *dev, unsigned long *mW,
+static int __maybe_unused _get_power(struct device *dev, unsigned long *uW,
 				     unsigned long *kHz)
 {
 	struct dev_pm_opp *opp;
@@ -1512,9 +1512,10 @@ static int __maybe_unused _get_power(struct device *dev, unsigned long *mW,
 		return -EINVAL;
 
 	tmp = (u64)cap * mV * mV * (Hz / 1000000);
-	do_div(tmp, 1000000000);
+	/* Provide power in micro-Watts */
+	do_div(tmp, 1000000);
 
-	*mW = (unsigned long)tmp;
+	*uW = (unsigned long)tmp;
 	*kHz = Hz / 1000;
 
 	return 0;

drivers/powercap/dtpm_cpu.c

@@ -53,7 +53,7 @@ static u64 set_pd_power_limit(struct dtpm *dtpm, u64 power_limit)
 
 	for (i = 0; i < pd->nr_perf_states; i++) {
 
-		power = pd->table[i].power * MICROWATT_PER_MILLIWATT * nr_cpus;
+		power = pd->table[i].power * nr_cpus;
 
 		if (power > power_limit)
 			break;
@@ -63,8 +63,7 @@ static u64 set_pd_power_limit(struct dtpm *dtpm, u64 power_limit)
 
 	freq_qos_update_request(&dtpm_cpu->qos_req, freq);
 
-	power_limit = pd->table[i - 1].power *
-		MICROWATT_PER_MILLIWATT * nr_cpus;
+	power_limit = pd->table[i - 1].power * nr_cpus;
 
 	return power_limit;
 }

drivers/thermal/cpufreq_cooling.c

@@ -21,6 +21,7 @@
 #include <linux/pm_qos.h>
 #include <linux/slab.h>
 #include <linux/thermal.h>
+#include <linux/units.h>
 
 #include <trace/events/thermal.h>
 
@@ -101,23 +102,31 @@ static unsigned long get_level(struct cpufreq_cooling_device *cpufreq_cdev,
 static u32 cpu_freq_to_power(struct cpufreq_cooling_device *cpufreq_cdev,
 			     u32 freq)
 {
+	unsigned long power_mw;
 	int i;
 
 	for (i = cpufreq_cdev->max_level - 1; i >= 0; i--) {
 		if (freq > cpufreq_cdev->em->table[i].frequency)
 			break;
 	}
 
-	return cpufreq_cdev->em->table[i + 1].power;
+	power_mw = cpufreq_cdev->em->table[i + 1].power;
+	power_mw /= MICROWATT_PER_MILLIWATT;
+
+	return power_mw;
 }
 
 static u32 cpu_power_to_freq(struct cpufreq_cooling_device *cpufreq_cdev,
 			     u32 power)
 {
+	unsigned long em_power_mw;
 	int i;
 
 	for (i = cpufreq_cdev->max_level; i > 0; i--) {
-		if (power >= cpufreq_cdev->em->table[i].power)
+		/* Convert EM power to milli-Watts to make safe comparison */
+		em_power_mw = cpufreq_cdev->em->table[i].power;
+		em_power_mw /= MICROWATT_PER_MILLIWATT;
+		if (power >= em_power_mw)
 			break;
 	}
 

drivers/thermal/devfreq_cooling.c

@@ -200,7 +200,11 @@ static int devfreq_cooling_get_requested_power(struct thermal_cooling_device *cd
 		res = dfc->power_ops->get_real_power(df, power, freq, voltage);
 		if (!res) {
 			state = dfc->capped_state;
+
+			/* Convert EM power into milli-Watts first */
 			dfc->res_util = dfc->em_pd->table[state].power;
+			dfc->res_util /= MICROWATT_PER_MILLIWATT;
+
 			dfc->res_util *= SCALE_ERROR_MITIGATION;
 
 			if (*power > 1)
@@ -218,8 +222,10 @@ static int devfreq_cooling_get_requested_power(struct thermal_cooling_device *cd
 
 		_normalize_load(&status);
 
-		/* Scale power for utilization */
+		/* Convert EM power into milli-Watts first */
 		*power = dfc->em_pd->table[perf_idx].power;
+		*power /= MICROWATT_PER_MILLIWATT;
+		/* Scale power for utilization */
 		*power *= status.busy_time;
 		*power >>= 10;
 	}
@@ -244,6 +250,7 @@ static int devfreq_cooling_state2power(struct thermal_cooling_device *cdev,
 
 	perf_idx = dfc->max_state - state;
 	*power = dfc->em_pd->table[perf_idx].power;
+	*power /= MICROWATT_PER_MILLIWATT;
 
 	return 0;
 }
@@ -254,7 +261,7 @@ static int devfreq_cooling_power2state(struct thermal_cooling_device *cdev,
 	struct devfreq_cooling_device *dfc = cdev->devdata;
 	struct devfreq *df = dfc->devfreq;
 	struct devfreq_dev_status status;
-	unsigned long freq;
+	unsigned long freq, em_power_mw;
 	s32 est_power;
 	int i;
 
@@ -279,9 +286,13 @@ static int devfreq_cooling_power2state(struct thermal_cooling_device *cdev,
 	 * Find the first cooling state that is within the power
 	 * budget. The EM power table is sorted ascending.
 	 */
-	for (i = dfc->max_state; i > 0; i--)
-		if (est_power >= dfc->em_pd->table[i].power)
+	for (i = dfc->max_state; i > 0; i--) {
+		/* Convert EM power to milli-Watts to make safe comparison */
+		em_power_mw = dfc->em_pd->table[i].power;
+		em_power_mw /= MICROWATT_PER_MILLIWATT;
+		if (est_power >= em_power_mw)
 			break;
+	}
 
 	*state = dfc->max_state - i;
 	dfc->capped_state = *state;

include/linux/energy_model.h

@@ -62,7 +62,7 @@ struct em_perf_domain {
 /*
  *  em_perf_domain flags:
  *
- *  EM_PERF_DOMAIN_MILLIWATTS: The power values are in milli-Watts or some
+ *  EM_PERF_DOMAIN_MICROWATTS: The power values are in micro-Watts or some
  *  other scale.
  *
  *  EM_PERF_DOMAIN_SKIP_INEFFICIENCIES: Skip inefficient states when estimating
@@ -71,30 +71,52 @@ struct em_perf_domain {
  *  EM_PERF_DOMAIN_ARTIFICIAL: The power values are artificial and might be
  *  created by platform missing real power information
  */
-#define EM_PERF_DOMAIN_MILLIWATTS BIT(0)
+#define EM_PERF_DOMAIN_MICROWATTS BIT(0)
 #define EM_PERF_DOMAIN_SKIP_INEFFICIENCIES BIT(1)
 #define EM_PERF_DOMAIN_ARTIFICIAL BIT(2)
 
 #define em_span_cpus(em) (to_cpumask((em)->cpus))
 #define em_is_artificial(em) ((em)->flags & EM_PERF_DOMAIN_ARTIFICIAL)
 
 #ifdef CONFIG_ENERGY_MODEL
-#define EM_MAX_POWER 0xFFFF
+/*
+ * The max power value in micro-Watts. The limit of 64 Watts is set as
+ * a safety net to not overflow multiplications on 32bit platforms. The
+ * 32bit value limit for total Perf Domain power implies a limit of
+ * maximum CPUs in such domain to 64.
+ */
+#define EM_MAX_POWER (64000000) /* 64 Watts */
+
+/*
+ * To avoid possible energy estimation overflow on 32bit machines add
+ * limits to number of CPUs in the Perf. Domain.
+ * We are safe on 64bit machine, thus some big number.
+ */
+#ifdef CONFIG_64BIT
+#define EM_MAX_NUM_CPUS 4096
+#else
+#define EM_MAX_NUM_CPUS 16
+#endif
 
 /*
- * Increase resolution of energy estimation calculations for 64-bit
- * architectures. The extra resolution improves decision made by EAS for the
- * task placement when two Performance Domains might provide similar energy
- * estimation values (w/o better resolution the values could be equal).
+ * To avoid an overflow on 32bit machines while calculating the energy
+ * use a different order in the operation. First divide by the 'cpu_scale'
+ * which would reduce big value stored in the 'cost' field, then multiply by
+ * the 'sum_util'. This would allow to handle existing platforms, which have
+ * e.g. power ~1.3 Watt at max freq, so the 'cost' value > 1mln micro-Watts.
+ * In such scenario, where there are 4 CPUs in the Perf. Domain the 'sum_util'
+ * could be 4096, then multiplication: 'cost' * 'sum_util'  would overflow.
+ * This reordering of operations has some limitations, we lose small
+ * precision in the estimation (comparing to 64bit platform w/o reordering).
  *
- * We increase resolution only if we have enough bits to allow this increased
- * resolution (i.e. 64-bit). The costs for increasing resolution when 32-bit
- * are pretty high and the returns do not justify the increased costs.
+ * We are safe on 64bit machine.
  */
 #ifdef CONFIG_64BIT
-#define em_scale_power(p) ((p) * 1000)
+#define em_estimate_energy(cost, sum_util, scale_cpu) \
+	(((cost) * (sum_util)) / (scale_cpu))
 #else
-#define em_scale_power(p) (p)
+#define em_estimate_energy(cost, sum_util, scale_cpu) \
+	(((cost) / (scale_cpu)) * (sum_util))
 #endif
 
 struct em_data_callback {
@@ -112,7 +134,7 @@ struct em_data_callback {
 	 * and frequency.
 	 *
 	 * In case of CPUs, the power is the one of a single CPU in the domain,
-	 * expressed in milli-Watts or an abstract scale. It is expected to
+	 * expressed in micro-Watts or an abstract scale. It is expected to
 	 * fit in the [0, EM_MAX_POWER] range.
 	 *
 	 * Return 0 on success.
@@ -148,7 +170,7 @@ struct em_perf_domain *em_cpu_get(int cpu);
 struct em_perf_domain *em_pd_get(struct device *dev);
 int em_dev_register_perf_domain(struct device *dev, unsigned int nr_states,
 				struct em_data_callback *cb, cpumask_t *span,
-				bool milliwatts);
+				bool microwatts);
 void em_dev_unregister_perf_domain(struct device *dev);
 
 /**
@@ -273,7 +295,7 @@ static inline unsigned long em_cpu_energy(struct em_perf_domain *pd,
 	 *   pd_nrg = ------------------------                       (4)
 	 *                  scale_cpu
 	 */
-	return ps->cost * sum_util / scale_cpu;
+	return em_estimate_energy(ps->cost, sum_util, scale_cpu);
 }
 
 /**
@@ -297,7 +319,7 @@ struct em_data_callback {};
 static inline
 int em_dev_register_perf_domain(struct device *dev, unsigned int nr_states,
 				struct em_data_callback *cb, cpumask_t *span,
-				bool milliwatts)
+				bool microwatts)
 {
 	return -EINVAL;
 }