Merge tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 "NAND:

    Quoting Boris:
     'This pull request contains only one notable change:
       - Addition of the MTK NAND controller driver

      And a bunch of specific NAND driver improvements/fixes. Here are the
      changes that are worth mentioning:
       - A few fixes/improvements for the xway NAND controller driver
       - A few fixes for the sunxi NAND controller driver
       - Support for DMA in the sunxi NAND driver
       - Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
       - Addition for bitflips detection in erased pages to the brcmnand driver
       - Support for new brcmnand IPs
       - Update of the OMAP-GPMC binding to support DMA channel description'

    In addition, some small fixes around error handling, etc., as well
    as one long-standing corner case issue (2.6.20, I think?) with
    writing 1 byte less than a page.

  NOR:

   - rework some error handling on reads and writes, so we can better
     handle (for instance) SPI controllers which have limitations on
     their maximum transfer size

   - add new Cadence Quad SPI flash controller driver

   - add new Atmel QSPI flash controller driver

   - add new Hisilicon SPI flash controller driver

   - support a few new flash, and update supported features on others

   - fix the logic used for detecting a fully-unlocked flash

  And other miscellaneous small fixes"

* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
  mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
  mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
  mtd: nand: fix bug writing 1 byte less than page size
  mtd: update description of MTD_BCM47XXSFLASH symbol
  mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
  mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
  mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
  mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
  mtd: maps: sa1100-flash: potential NULL dereference
  mtd: atmel-quadspi: add driver for Atmel QSPI controller
  mtd: nand: omap2: fix return value check in omap_nand_probe()
  Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
  mtd: spi-nor: add hisilicon spi-nor flash controller driver
  mtd: spi-nor: support dual, quad, and WP for Gigadevice
  mtd: spi-nor: Added support for n25q00a.
  memory: Update dependency of IFC for Layerscape
  mtd: nand: jz4780: Update MODULE_AUTHOR email address
  mtd: nand: sunxi: prevent a small memory leak
  mtd: nand: sunxi: add reset line support
  mtd: nand: sunxi: update DT bindings
  ...

Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt

@@ -46,6 +46,10 @@ Required properties:
 			0 maps to GPMC_WAIT0 pin.
  - gpio-cells:		Must be set to 2
 
+Required properties when using NAND prefetch dma:
+ - dmas			GPMC NAND prefetch dma channel
+ - dma-names		Must be set to "rxtx"
+
 Timing properties for child nodes. All are optional and default to 0.
 
  - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
@@ -137,7 +141,8 @@ Example for an AM33xx board:
 		ti,hwmods = "gpmc";
 		reg = <0x50000000 0x2000>;
 		interrupts = <100>;
-
+		dmas = <&edma 52 0>;
+		dma-names = "rxtx";
 		gpmc,num-cs = <8>;
 		gpmc,num-waitpins = <2>;
 		#address-cells = <2>;

Documentation/devicetree/bindings/mtd/atmel-quadspi.txt

@@ -0,0 +1,32 @@
+* Atmel Quad Serial Peripheral Interface (QSPI)
+
+Required properties:
+- compatible:     Should be "atmel,sama5d2-qspi".
+- reg:            Should contain the locations and lengths of the base registers
+                  and the mapped memory.
+- reg-names:      Should contain the resource reg names:
+                  - qspi_base: configuration register address space
+                  - qspi_mmap: memory mapped address space
+- interrupts:     Should contain the interrupt for the device.
+- clocks:         The phandle of the clock needed by the QSPI controller.
+- #address-cells: Should be <1>.
+- #size-cells:    Should be <0>.
+
+Example:
+
+spi@f0020000 {
+	compatible = "atmel,sama5d2-qspi";
+	reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>;
+	reg-names = "qspi_base", "qspi_mmap";
+	interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>;
+	clocks = <&spi0_clk>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0_default>;
+	status = "okay";
+
+	m25p80@0 {
+		...
+	};
+};

Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

@@ -27,6 +27,7 @@ Required properties:
                          brcm,brcmnand-v6.2
                          brcm,brcmnand-v7.0
                          brcm,brcmnand-v7.1
+                         brcm,brcmnand-v7.2
                          brcm,brcmnand
 - reg              : the register start and length for NAND register region.
                      (optional) Flash DMA register range (if present)

Documentation/devicetree/bindings/mtd/cadence-quadspi.txt

@@ -0,0 +1,56 @@
+* Cadence Quad SPI controller
+
+Required properties:
+- compatible : Should be "cdns,qspi-nor".
+- reg : Contains two entries, each of which is a tuple consisting of a
+	physical address and length. The first entry is the address and
+	length of the controller register set. The second entry is the
+	address and length of the QSPI Controller data area.
+- interrupts : Unit interrupt specifier for the controller interrupt.
+- clocks : phandle to the Quad SPI clock.
+- cdns,fifo-depth : Size of the data FIFO in words.
+- cdns,fifo-width : Bus width of the data FIFO in bytes.
+- cdns,trigger-address : 32-bit indirect AHB trigger address.
+
+Optional properties:
+- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
+
+Optional subnodes:
+Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
+custom properties:
+- cdns,read-delay : Delay for read capture logic, in clock cycles
+- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
+                  mode chip select outputs are de-asserted between
+		  transactions.
+- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
+                  de-activated and the activation of another.
+- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
+                  transaction and deasserting the device chip select
+		  (qspi_n_ss_out).
+- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
+                  and first bit transfer.
+
+Example:
+
+	qspi: spi@ff705000 {
+		compatible = "cdns,qspi-nor";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xff705000 0x1000>,
+		      <0xffa00000 0x1000>;
+		interrupts = <0 151 4>;
+		clocks = <&qspi_clk>;
+		cdns,is-decoded-cs;
+		cdns,fifo-depth = <128>;
+		cdns,fifo-width = <4>;
+		cdns,trigger-address = <0x00000000>;
+
+		flash0: n25q00@0 {
+			...
+			cdns,read-delay = <4>;
+			cdns,tshsl-ns = <50>;
+			cdns,tsd2d-ns = <50>;
+			cdns,tchsh-ns = <4>;
+			cdns,tslch-ns = <4>;
+		};
+	};

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -39,7 +39,7 @@ Optional properties:
 
 		"prefetch-polled"	Prefetch polled mode (default)
 		"polled"		Polled mode, without prefetch
-		"prefetch-dma"		Prefetch enabled sDMA mode
+		"prefetch-dma"		Prefetch enabled DMA mode
 		"prefetch-irq"		Prefetch enabled irq mode
 
  - elm_id:	<deprecated> use "ti,elm-id" instead

Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt

@@ -0,0 +1,24 @@
+HiSilicon SPI-NOR Flash Controller
+
+Required properties:
+- compatible : Should be "hisilicon,fmc-spi-nor" and one of the following strings:
+		"hisilicon,hi3519-spi-nor"
+- address-cells : Should be 1.
+- size-cells : Should be 0.
+- reg : Offset and length of the register set for the controller device.
+- reg-names : Must include the following two entries: "control", "memory".
+- clocks : handle to spi-nor flash controller clock.
+
+Example:
+spi-nor-controller@10000000 {
+	compatible = "hisilicon,hi3519-spi-nor", "hisilicon,fmc-spi-nor";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x10000000 0x1000>, <0x14000000 0x1000000>;
+	reg-names = "control", "memory";
+	clocks = <&clock HI3519_FMC_CLK>;
+	spi-nor@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+	};
+};

Documentation/devicetree/bindings/mtd/mtk-nand.txt

@@ -0,0 +1,160 @@
+MTK SoCs NAND FLASH controller (NFC) DT binding
+
+This file documents the device tree bindings for MTK SoCs NAND controllers.
+The functional split of the controller requires two drivers to operate:
+the nand controller interface driver and the ECC engine driver.
+
+The hardware description for both devices must be captured as device
+tree nodes.
+
+1) NFC NAND Controller Interface (NFI):
+=======================================
+
+The first part of NFC is NAND Controller Interface (NFI) HW.
+Required NFI properties:
+- compatible:			Should be "mediatek,mtxxxx-nfc".
+- reg:				Base physical address and size of NFI.
+- interrupts:			Interrupts of NFI.
+- clocks:			NFI required clocks.
+- clock-names:			NFI clocks internal name.
+- status:			Disabled default. Then set "okay" by platform.
+- ecc-engine:			Required ECC Engine node.
+- #address-cells:		NAND chip index, should be 1.
+- #size-cells:			Should be 0.
+
+Example:
+
+	nandc: nfi@1100d000 {
+		compatible = "mediatek,mt2701-nfc";
+		reg = <0 0x1100d000 0 0x1000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI>,
+			 <&pericfg CLK_PERI_NFI_PAD>;
+		clock-names = "nfi_clk", "pad_clk";
+		status = "disabled";
+		ecc-engine = <&bch>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+        };
+
+Platform related properties, should be set in {platform_name}.dts:
+- children nodes:	NAND chips.
+
+Children nodes properties:
+- reg:			Chip Select Signal, default 0.
+			Set as reg = <0>, <1> when need 2 CS.
+Optional:
+- nand-on-flash-bbt:	Store BBT on NAND Flash.
+- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
+- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
+			valid values: 512 and 1024.
+			1024 is recommended for large page NANDs.
+- nand-ecc-strength:	Number of bits to correct per ECC step.
+			The valid values that the controller supports are: 4, 6,
+			8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44,
+			48, 52, 56, 60.
+			The strength should be calculated as follows:
+			E = (S - F) * 8 / 14
+			S = O / (P / Q)
+				E :	nand-ecc-strength.
+				S :	spare size per sector.
+				F :	FDM size, should be in the range [1,8].
+					It is used to store free oob data.
+				O :	oob size.
+				P :	page size.
+				Q :	nand-ecc-step-size.
+			If the result does not match any one of the listed
+			choices above, please select the smaller valid value from
+			the list.
+			(otherwise the driver will do the adjustment at runtime)
+- pinctrl-names:	Default NAND pin GPIO setting name.
+- pinctrl-0:		GPIO setting node.
+
+Example:
+	&pio {
+		nand_pins_default: nanddefault {
+			pins_dat {
+				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
+					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
+					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
+					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
+					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
+					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
+					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
+					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
+					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
+				input-enable;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up;
+			};
+
+			pins_we {
+				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+			};
+
+			pins_ale {
+				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+			};
+		};
+	};
+
+	&nandc {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&nand_pins_default>;
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <24>;
+			nand-ecc-step-size = <1024>;
+		};
+	};
+
+NAND chip optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			preloader@0 {
+				label = "pl";
+				read-only;
+				reg = <0x00000000 0x00400000>;
+			};
+			android@0x00400000 {
+				label = "android";
+				reg = <0x00400000 0x12c00000>;
+			};
+		};
+	};
+
+2) ECC Engine:
+==============
+
+Required BCH properties:
+- compatible:	Should be "mediatek,mtxxxx-ecc".
+- reg:		Base physical address and size of ECC.
+- interrupts:	Interrupts of ECC.
+- clocks:	ECC required clocks.
+- clock-names:	ECC clocks internal name.
+- status:	Disabled default. Then set "okay" by platform.
+
+Example:
+
+	bch: ecc@1100e000 {
+		compatible = "mediatek,mt2701-ecc";
+		reg = <0 0x1100e000 0 0x1000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI_ECC>;
+		clock-names = "nfiecc_clk";
+		status = "disabled";
+	};

Documentation/devicetree/bindings/mtd/sunxi-nand.txt

@@ -11,10 +11,16 @@ Required properties:
     * "ahb" : AHB gating clock
     * "mod" : nand controller clock
 
+Optional properties:
+- dmas : shall reference DMA channel associated to the NAND controller.
+- dma-names : shall be "rxtx".
+
 Optional children nodes:
 Children nodes represent the available nand chips.
 
 Optional properties:
+- reset : phandle + reset specifier pair
+- reset-names : must contain "ahb"
 - allwinner,rb : shall contain the native Ready/Busy ids.
  or
 - rb-gpios : shall contain the gpios used as R/B pins.

arch/cris/arch-v10/drivers/axisflashmap.c

@@ -397,7 +397,7 @@ static int __init init_axis_flash(void)
 	if (!romfs_in_flash) {
 		/* Create an RAM device for the root partition (romfs). */
 
-#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) || (CONFIG_MTDRAM_ABS_POS != 0)
+#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0)
 		/* No use trying to boot this kernel from RAM. Panic! */
 		printk(KERN_EMERG "axisflashmap: Cannot create an MTD RAM "
 		       "device due to kernel (mis)configuration!\n");

arch/cris/arch-v32/drivers/axisflashmap.c

@@ -320,7 +320,7 @@ static int __init init_axis_flash(void)
 	 * but its size must be configured as 0 so as not to conflict
 	 * with our usage.
 	 */
-#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) || (CONFIG_MTDRAM_ABS_POS != 0)
+#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0)
 	if (!romfs_in_flash && !nand_boot) {
 		printk(KERN_EMERG "axisflashmap: Cannot create an MTD RAM "
 		       "device; configure CONFIG_MTD_MTDRAM with size = 0!\n");

drivers/memory/Kconfig

@@ -115,7 +115,7 @@ config FSL_CORENET_CF
 
 config FSL_IFC
 	bool
-	depends on FSL_SOC
+	depends on FSL_SOC || ARCH_LAYERSCAPE
 
 config JZ4780_NEMC
 	bool "Ingenic JZ4780 SoC NEMC driver"

drivers/memory/fsl_ifc.c

@@ -31,7 +31,9 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/fsl_ifc.h>
-#include <asm/prom.h>
+#include <linux/irqdomain.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
 
 struct fsl_ifc_ctrl *fsl_ifc_ctrl_dev;
 EXPORT_SYMBOL(fsl_ifc_ctrl_dev);

drivers/mtd/chips/cfi_cmdset_0020.c

@@ -416,7 +416,7 @@ static int cfi_staa_read (struct mtd_info *mtd, loff_t from, size_t len, size_t
 	return ret;
 }
 
-static inline int do_write_buffer(struct map_info *map, struct flchip *chip,
+static int do_write_buffer(struct map_info *map, struct flchip *chip,
 				  unsigned long adr, const u_char *buf, int len)
 {
 	struct cfi_private *cfi = map->fldrv_priv;