Merge tag 'at24-4.19-updates-for-wolfram' of git://git.kernel.org/pub…

…/scm/linux/kernel/git/brgl/linux into i2c/for-4.19 at24: updates for v4.19 New property: 'address-width' which allows to specify the number of addressing bits. Up until now we only could choose one of the defined models and rely on the flags specified in its corresponding chip data structure.
mariux64 · Jul 29, 2018 · b1d2b0a · b1d2b0a
2 parents 3b77001 + a2b3bf4
commit b1d2b0a
Show file tree

Hide file tree

Showing 358 changed files with 3,093 additions and 1,722 deletions.
diff --git a/Documentation/device-mapper/writecache.txt b/Documentation/device-mapper/writecache.txt
@@ -15,6 +15,8 @@ Constructor parameters:
    size)
 5. the number of optional parameters (the parameters with an argument
    count as two)
+	start_sector n		(default: 0)
+		offset from the start of cache device in 512-byte sectors
 	high_watermark n	(default: 50)
 		start writeback when the number of used blocks reach this
 		watermark

diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
@@ -66,7 +66,7 @@ Required root node properties:
 	- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
 				    Octa board.
 	- "insignal,origen"       - for Exynos4210-based Insignal Origen board.
-	- "insignal,origen4412    - for Exynos4412-based Insignal Origen board.
+	- "insignal,origen4412"   - for Exynos4412-based Insignal Origen board.
 
 
 Optional nodes:

diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
@@ -36,7 +36,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting

diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt
@@ -72,6 +72,8 @@ Optional properties:
 
   - wp-gpios: GPIO to which the write-protect pin of the chip is connected.
 
+  - address-width: number of address bits (one of 8, 16).
+
 Example:
 
 eeprom@52 {

diff --git a/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt b/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt
@@ -1,7 +1,7 @@
 Nintendo Wii (Hollywood) GPIO controller
 
 Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
 - reg: Physical base address and length of the controller's registers.
 - gpio-controller: Marks the device node as a GPIO controller.
 - #gpio-cells: Should be <2>. The first cell is the pin number and the

diff --git a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt
@@ -32,7 +32,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;

diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt
@@ -15,7 +15,7 @@ Required properties:
   include "nvidia,tegra30-ictlr".	
 - reg : Specifies base physical address and size of the registers.
   Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5"  
+  whereas Tegra30 and later have 5).
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value must be 3.

diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt
@@ -12,7 +12,7 @@ Required properties:
   specifier, shall be 2
 - interrupts: interrupts references to primary interrupt controller
   (only needed for exti controller with multiple exti under
-  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+  same parent interrupt: st,stm32-exti and st,stm32h7-exti)
 
 Example:
 

diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt
@@ -152,7 +152,7 @@ Required properties:
 - compatible	: should contain one of:
 		  "brcm,bcm7425-timers"
 		  "brcm,bcm7429-timers"
-		  "brcm,bcm7435-timers and
+		  "brcm,bcm7435-timers" and
 		  "brcm,brcmstb-timers"
 - reg		: the timers register range
 - interrupts	: the interrupt line for this timer block

diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt
@@ -238,7 +238,7 @@ PROPERTIES
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
-		- "fsl,fman-memac for mEMAC MAC
+		- "fsl,fman-memac" for mEMAC MAC
 
 - cell-index
 		Usage: required

diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt
@@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
 node with the label "power".
 In the second example the consumer device are partitioned across two PM domains,
 the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
 
 Optional properties:
 - required-opps: This contains phandle to an OPP node in another device's OPP

diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt
@@ -16,7 +16,7 @@ Required properties:
 Optional properties:
 - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled and if it is from GPIO then GPIO
   number should be provided. If it is externally controlled and no GPIO
   entry then driver will just configure this rails as external control

diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt
@@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
 - #reset-cells: 1, see below
 
 example:

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -39,7 +39,7 @@ Required properties:
 
 Optional property:
 - clock-frequency:	Desired I2C bus clock frequency in Hz.
-			When missing default to 400000Hz.
+			When missing default to 100000Hz.
 
 Child nodes should conform to I2C bus binding as described in i2c.txt.
 

diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt
@@ -30,7 +30,7 @@ Required properties:
 
 			  Board connectors:
 			  * Headset Mic
-			  * Secondary Mic",
+			  * Secondary Mic
 			  * DMIC
 			  * Ext Spk
 

diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt
@@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
 			"Digital Mic3"
 
 		Audio pins and MicBias on WCD9335 Codec:
-			"MIC_BIAS1
+			"MIC_BIAS1"
 			"MIC_BIAS2"
 			"MIC_BIAS3"
 			"MIC_BIAS4"

diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt
@@ -15,7 +15,7 @@ Optional properties:
 
 Examples:
 
-	onewire@0 {
+	onewire {
 		compatible = "w1-gpio";
 		gpios = <&gpio 126 0>, <&gpio 105 0>;
 	};

diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt
@@ -1490,7 +1490,7 @@ To remove an ARP target:
 
 To configure the interval between learning packet transmits:
 # echo 12 > /sys/class/net/bond0/bonding/lp_interval
-	NOTE: the lp_inteval is the number of seconds between instances where
+	NOTE: the lp_interval is the number of seconds between instances where
 the bonding driver sends learning packets to each slaves peer switch.  The
 default interval is 1 second.
 

diff --git a/Documentation/networking/e100.rst b/Documentation/networking/e100.rst
@@ -47,41 +47,45 @@ Driver Configuration Parameters
 The default value for each parameter is generally the recommended setting,
 unless otherwise noted.
 
-Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
+Rx Descriptors:
+   Number of receive descriptors. A receive descriptor is a data
    structure that describes a receive buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to write
    data from the controller to host memory. In the 3.x.x driver the valid range
    for this parameter is 64-256. The default value is 256. This parameter can be
    changed using the command::
 
-   ethtool -G eth? rx n
+     ethtool -G eth? rx n
 
    Where n is the number of desired Rx descriptors.
 
-Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
+Tx Descriptors:
+   Number of transmit descriptors. A transmit descriptor is a data
    structure that describes a transmit buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to read
    data from the host memory to the controller. In the 3.x.x driver the valid
    range for this parameter is 64-256. The default value is 128. This parameter
    can be changed using the command::
 
-   ethtool -G eth? tx n
+     ethtool -G eth? tx n
 
    Where n is the number of desired Tx descriptors.
 
-Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
+Speed/Duplex:
+   The driver auto-negotiates the link speed and duplex settings by
    default. The ethtool utility can be used as follows to force speed/duplex.::
 
-   ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
+     ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
 
    NOTE: setting the speed/duplex to incorrect values will cause the link to
    fail.
 
-Event Log Message Level:  The driver uses the message level flag to log events
+Event Log Message Level:
+   The driver uses the message level flag to log events
    to syslog. The message level can be set at driver load time. It can also be
    set using the command::
 
-   ethtool -s eth? msglvl n
+     ethtool -s eth? msglvl n
 
 
 Additional Configurations
@@ -92,7 +96,7 @@ Configuring the Driver on Different Distributions
 
 Configuring a network driver to load properly when the system is started
 is distribution dependent.  Typically, the configuration process involves
-adding an alias line to /etc/modprobe.d/*.conf as well as editing other
+adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other
 system startup scripts and/or configuration files.  Many popular Linux
 distributions ship with tools to make these changes for you.  To learn
 the proper way to configure a network device for your system, refer to
@@ -160,7 +164,10 @@ This results in unbalanced receive traffic.
 If you have multiple interfaces in a server, either turn on ARP
 filtering by
 
-(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+(1) entering::
+
+	echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+
     (this only works if your kernel's version is higher than 2.4.5), or
 
 (2) installing the interfaces in separate broadcast domains (either