igb: add support for 82580 MAC

This patch adds support for the 82580 MAC.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/igb/e1000_82575.h

@@ -38,6 +38,11 @@ extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw);
 
 #define E1000_RAR_ENTRIES_82575   16
 #define E1000_RAR_ENTRIES_82576   24
+#define E1000_RAR_ENTRIES_82580   24
+
+#define E1000_SW_SYNCH_MB              0x00000100
+#define E1000_STAT_DEV_RST_SET         0x00100000
+#define E1000_CTRL_DEV_RST             0x20000000
 
 /* SRRCTL bit definitions */
 #define E1000_SRRCTL_BSIZEPKT_SHIFT                     10 /* Shift _right_ */
@@ -232,5 +237,6 @@ struct e1000_adv_tx_context_desc {
 #define E1000_RXPBS_SIZE_MASK_82576  0x0000007F
 void igb_vmdq_set_loopback_pf(struct e1000_hw *, bool);
 void igb_vmdq_set_replication_pf(struct e1000_hw *, bool);
+u16 igb_rxpbs_adjust_82580(u32 data);
 
 #endif

drivers/net/igb/e1000_defines.h

@@ -49,6 +49,7 @@
 #define E1000_CTRL_EXT_PFRSTD    0x00004000
 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES  0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX  0x00400000
 #define E1000_CTRL_EXT_LINK_MODE_SGMII   0x00800000
 #define E1000_CTRL_EXT_EIAME          0x01000000
 #define E1000_CTRL_EXT_IRCA           0x00000001
@@ -557,8 +558,12 @@
 #define NVM_ALT_MAC_ADDR_PTR       0x0037
 #define NVM_CHECKSUM_REG           0x003F
 
-#define E1000_NVM_CFG_DONE_PORT_0  0x40000 /* MNG config cycle done */
-#define E1000_NVM_CFG_DONE_PORT_1  0x80000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_0  0x040000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1  0x080000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_2  0x100000 /* ...for third port */
+#define E1000_NVM_CFG_DONE_PORT_3  0x200000 /* ...for fourth port */
+
+#define NVM_82580_LAN_FUNC_OFFSET(a) (a ? (0x40 + (0x40 * a)) : 0)
 
 /* Mask bits for fields in Word 0x0f of the NVM */
 #define NVM_WORD0F_PAUSE_MASK       0x3000
@@ -625,6 +630,7 @@
  */
 #define M88E1111_I_PHY_ID    0x01410CC0
 #define IGP03E1000_E_PHY_ID  0x02A80390
+#define I82580_I_PHY_ID      0x015403A0
 #define M88_VENDOR           0x0141
 
 /* M88E1000 Specific Registers */

drivers/net/igb/e1000_hw.h

@@ -47,19 +47,30 @@ struct e1000_hw;
 #define E1000_DEV_ID_82575EB_COPPER           0x10A7
 #define E1000_DEV_ID_82575EB_FIBER_SERDES     0x10A9
 #define E1000_DEV_ID_82575GB_QUAD_COPPER      0x10D6
+#define E1000_DEV_ID_82580_COPPER             0x150E
+#define E1000_DEV_ID_82580_FIBER              0x150F
+#define E1000_DEV_ID_82580_SERDES             0x1510
+#define E1000_DEV_ID_82580_SGMII              0x1511
+#define E1000_DEV_ID_82580_COPPER_DUAL        0x1516
 
 #define E1000_REVISION_2 2
 #define E1000_REVISION_4 4
 
 #define E1000_FUNC_0     0
 #define E1000_FUNC_1     1
+#define E1000_FUNC_2     2
+#define E1000_FUNC_3     3
 
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0   0
 #define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1   3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN2   6
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN3   9
 
 enum e1000_mac_type {
 	e1000_undefined = 0,
 	e1000_82575,
 	e1000_82576,
+	e1000_82580,
 	e1000_num_macs  /* List is 1-based, so subtract 1 for true count. */
 };
 
@@ -290,6 +301,7 @@ struct e1000_mac_operations {
 
 struct e1000_phy_operations {
 	s32  (*acquire)(struct e1000_hw *);
+	s32  (*check_polarity)(struct e1000_hw *);
 	s32  (*check_reset_block)(struct e1000_hw *);
 	s32  (*force_speed_duplex)(struct e1000_hw *);
 	s32  (*get_cfg_done)(struct e1000_hw *hw);
@@ -466,6 +478,7 @@ struct e1000_mbx_info {
 
 struct e1000_dev_spec_82575 {
 	bool sgmii_active;
+	bool global_device_reset;
 };
 
 struct e1000_hw {

drivers/net/igb/e1000_phy.c

@@ -136,7 +136,7 @@ static s32 igb_phy_reset_dsp(struct e1000_hw *hw)
  *  Reads the MDI control regsiter in the PHY at offset and stores the
  *  information read to data.
  **/
-static s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	u32 i, mdic = 0;
@@ -194,7 +194,7 @@ static s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
  *
  *  Writes data to MDI control register in the PHY at offset.
  **/
-static s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	u32 i, mdic = 0;
@@ -1947,7 +1947,7 @@ s32 igb_phy_init_script_igp3(struct e1000_hw *hw)
  *
  *  Polarity is determined based on the PHY specific status register.
  **/
-s32 igb_check_polarity_82580(struct e1000_hw *hw)
+static s32 igb_check_polarity_82580(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	s32 ret_val;

drivers/net/igb/e1000_phy.h

@@ -61,10 +61,11 @@ s32  igb_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
 				u32 usec_interval, bool *success);
 s32  igb_phy_init_script_igp3(struct e1000_hw *hw);
+s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
 s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_copper_link_setup_82580(struct e1000_hw *hw);
-s32  igb_check_polarity_82580(struct e1000_hw *hw);
 s32  igb_get_phy_info_82580(struct e1000_hw *hw);
 s32  igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
 s32  igb_get_cable_length_82580(struct e1000_hw *hw);

drivers/net/igb/e1000_regs.h

@@ -34,6 +34,7 @@
 #define E1000_EERD     0x00014  /* EEPROM Read - RW */
 #define E1000_CTRL_EXT 0x00018  /* Extended Device Control - RW */
 #define E1000_MDIC     0x00020  /* MDI Control - RW */
+#define E1000_MDICNFG  0x00E04  /* MDI Config - RW */
 #define E1000_SCTL     0x00024  /* SerDes Control - RW */
 #define E1000_FCAL     0x00028  /* Flow Control Address Low - RW */
 #define E1000_FCAH     0x0002C  /* Flow Control Address High -RW */