Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/…

…kernel/git/swarren/linux-tegra into next/soc

From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12

This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:

* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
  just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
  both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
  from arch/arm/mach-tegra/ to drivers/pci/host/.

The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.

* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
  ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
  MAINTAINERS: Add myself as Tegra PCIe maintainer
  PCI: tegra: set up PADS_REFCLK_CFG1
  PCI: tegra: Add Tegra 30 PCIe support
  PCI: tegra: Move PCIe driver to drivers/pci/host
  PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
  ARM: tegra: add LP1 suspend support for Tegra114
  ARM: tegra: add LP1 suspend support for Tegra20
  ARM: tegra: add LP1 suspend support for Tegra30
  ARM: tegra: add common LP1 suspend support
  clk: tegra114: add LP1 suspend/resume support
  ARM: tegra: config the polarity of the request of sys clock
  ARM: tegra: add common resume handling code for LP1 resuming
  ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
  of: pci: add registry of MSI chips
  PCI: Introduce new MSI chip infrastructure
  PCI: remove ARCH_SUPPORTS_MSI kconfig option
  PCI: use weak functions for MSI arch-specific functions
  ARM: tegra: unify Tegra's Kconfig a bit more
  ARM: tegra: remove the limitation that Tegra114 can't support suspend
  ...

Signed-off-by: Kevin Hilman <khilman@linaro.org>

Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt

@@ -0,0 +1,163 @@
+NVIDIA Tegra PCIe controller
+
+Required properties:
+- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie"
+- device_type: Must be "pci"
+- reg: A list of physical base address and length for each set of controller
+  registers. Must contain an entry for each entry in the reg-names property.
+- reg-names: Must include the following entries:
+  "pads": PADS registers
+  "afi": AFI registers
+  "cs": configuration space region
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+  "intr": The Tegra interrupt that is asserted for controller interrupts
+  "msi": The Tegra interrupt that is asserted when an MSI is received
+- pex-clk-supply: Supply voltage for internal reference clock
+- vdd-supply: Power supply for controller (1.05V)
+- avdd-supply: Power supply for controller (1.05V) (not required for Tegra20)
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+  - cell 0 specifies the bus and device numbers of the root port:
+    [23:16]: bus number
+    [15:11]: device number
+  - cell 1 denotes the upper 32 address bits and should be 0
+  - cell 2 contains the lower 32 address bits and is used to translate to the
+    CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+  PCI regions. The entries must be 6 cells each, where the first three cells
+  correspond to the address as described for the #address-cells property
+  above, the fourth cell is the physical CPU address to translate to and the
+  fifth and six cells are as described for the #size-cells property above.
+  - The first two entries are expected to translate the addresses for the root
+    port registers, which are referenced by the assigned-addresses property of
+    the root port nodes (see below).
+  - The remaining entries setup the mapping for the standard I/O, memory and
+    prefetchable PCI regions. The first cell determines the type of region
+    that is setup:
+    - 0x81000000: I/O memory region
+    - 0x82000000: non-prefetchable memory region
+    - 0xc2000000: prefetchable memory region
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- clocks: List of clock inputs of the controller. Must contain an entry for
+  each entry in the clock-names property.
+- clock-names: Must include the following entries:
+  "pex": The Tegra clock of that name
+  "afi": The Tegra clock of that name
+  "pcie_xclk": The Tegra clock of that name
+  "pll_e": The Tegra clock of that name
+  "cml": The Tegra clock of that name (not required for Tegra20)
+
+Root ports are defined as subnodes of the PCIe controller node.
+
+Required properties:
+- device_type: Must be "pci"
+- assigned-addresses: Address and size of the port configuration registers
+- reg: PCI bus address of the root port
+- #address-cells: Must be 3
+- #size-cells: Must be 2
+- ranges: Sub-ranges distributed from the PCIe controller node. An empty
+  property is sufficient.
+- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations
+  are:
+  - Root port 0 uses 4 lanes, root port 1 is unused.
+  - Both root ports use 2 lanes.
+
+Example:
+
+SoC DTSI:
+
+	pcie-controller {
+		compatible = "nvidia,tegra20-pcie";
+		device_type = "pci";
+		reg = <0x80003000 0x00000800   /* PADS registers */
+		       0x80003800 0x00000200   /* AFI registers */
+		       0x90000000 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <0 98 0x04   /* controller interrupt */
+		              0 99 0x04>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000   /* port 0 registers */
+			  0x82000000 0 0x80001000 0x80001000 0 0x00001000   /* port 1 registers */
+			  0x81000000 0 0          0x82000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0xa0000000 0xa0000000 0 0x10000000   /* non-prefetchable memory */
+			  0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */
+
+		clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>,
+			 <&tegra_car 118>;
+		clock-names = "pex", "afi", "pcie_xclk", "pll_e";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+	};
+
+
+Board DTS:
+
+	pcie-controller {
+		status = "okay";
+
+		vdd-supply = <&pci_vdd_reg>;
+		pex-clk-supply = <&pci_clk_reg>;
+
+		/* root port 00:01.0 */
+		pci@1,0 {
+			status = "okay";
+
+			/* bridge 01:00.0 (optional) */
+			pci@0,0 {
+				reg = <0x010000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				device_type = "pci";
+
+				/* endpoint 02:00.0 */
+				pci@0,0 {
+					reg = <0x020000 0 0 0 0>;
+				};
+			};
+		};
+	};
+
+Note that devices on the PCI bus are dynamically discovered using PCI's bus
+enumeration and therefore don't need corresponding device nodes in DT. However
+if a device on the PCI bus provides a non-probeable bus such as I2C or SPI,
+device nodes need to be added in order to allow the bus' children to be
+instantiated at the proper location in the operating system's device tree (as
+illustrated by the optional nodes in the example above).

MAINTAINERS

@@ -6275,6 +6275,13 @@ F:	Documentation/PCI/
 F:	drivers/pci/
 F:	include/linux/pci*
 
+PCI DRIVER FOR NVIDIA TEGRA
+M:	Thierry Reding <thierry.reding@gmail.com>
+L:	linux-tegra@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
+F:	drivers/pci/host/pci-tegra.c
+
 PCMCIA SUBSYSTEM
 P:	Linux PCMCIA Team
 L:	linux-pcmcia@lists.infradead.org

arch/arm/Kconfig

@@ -441,7 +441,6 @@ config ARCH_NETX
 config ARCH_IOP13XX
 	bool "IOP13xx-based"
 	depends on MMU
-	select ARCH_SUPPORTS_MSI
 	select CPU_XSC3
 	select NEED_MACH_MEMORY_H
 	select NEED_RET_TO_USER

arch/arm/include/asm/mach/pci.h

@@ -36,6 +36,8 @@ struct hw_pci {
 					  resource_size_t start,
 					  resource_size_t size,
 					  resource_size_t align);
+	void		(*add_bus)(struct pci_bus *bus);
+	void		(*remove_bus)(struct pci_bus *bus);
 };
 
 /*
@@ -63,6 +65,8 @@ struct pci_sys_data {
 					  resource_size_t start,
 					  resource_size_t size,
 					  resource_size_t align);
+	void		(*add_bus)(struct pci_bus *bus);
+	void		(*remove_bus)(struct pci_bus *bus);
 	void		*private_data;	/* platform controller private data	*/
 };
 

arch/arm/kernel/bios32.c

@@ -363,6 +363,20 @@ void pcibios_fixup_bus(struct pci_bus *bus)
 }
 EXPORT_SYMBOL(pcibios_fixup_bus);
 
+void pcibios_add_bus(struct pci_bus *bus)
+{
+	struct pci_sys_data *sys = bus->sysdata;
+	if (sys->add_bus)
+		sys->add_bus(bus);
+}
+
+void pcibios_remove_bus(struct pci_bus *bus)
+{
+	struct pci_sys_data *sys = bus->sysdata;
+	if (sys->remove_bus)
+		sys->remove_bus(bus);
+}
+
 /*
  * Swizzle the device pin each time we cross a bridge.  If a platform does
  * not provide a swizzle function, we perform the standard PCI swizzling.
@@ -464,6 +478,8 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		sys->swizzle = hw->swizzle;
 		sys->map_irq = hw->map_irq;
 		sys->align_resource = hw->align_resource;
+		sys->add_bus = hw->add_bus;
+		sys->remove_bus = hw->remove_bus;
 		INIT_LIST_HEAD(&sys->resources);
 
 		if (hw->private_data)

arch/arm/mach-tegra/Kconfig

@@ -2,19 +2,27 @@ config ARCH_TEGRA
 	bool "NVIDIA Tegra" if ARCH_MULTI_V7
 	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
+	select ARM_GIC
 	select CLKDEV_LOOKUP
 	select CLKSRC_MMIO
 	select CLKSRC_OF
 	select COMMON_CLK
+	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if LOCAL_TIMERS
 	select HAVE_CLK
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
+	select PINCTRL
 	select SOC_BUS
 	select SPARSE_IRQ
+	select USB_ARCH_HAS_EHCI if USB_SUPPORT
+	select USB_ULPI if USB_PHY
+	select USB_ULPI_VIEWPORT if USB_PHY
 	select USE_OF
+	select MIGHT_HAVE_PCI
+	select ARCH_SUPPORTS_MSI
 	help
 	  This enables support for NVIDIA Tegra based systems.
 
@@ -27,15 +35,9 @@ config ARCH_TEGRA_2x_SOC
 	select ARM_ERRATA_720789
 	select ARM_ERRATA_754327 if SMP
 	select ARM_ERRATA_764369 if SMP
-	select ARM_GIC
-	select CPU_V7
-	select PINCTRL
 	select PINCTRL_TEGRA20
 	select PL310_ERRATA_727915 if CACHE_L2X0
 	select PL310_ERRATA_769419 if CACHE_L2X0
-	select USB_ARCH_HAS_EHCI if USB_SUPPORT
-	select USB_ULPI if USB_PHY
-	select USB_ULPI_VIEWPORT if USB_PHY
 	help
 	  Support for NVIDIA Tegra AP20 and T20 processors, based on the
 	  ARM CortexA9MP CPU and the ARM PL310 L2 cache controller
@@ -44,35 +46,22 @@ config ARCH_TEGRA_3x_SOC
 	bool "Enable support for Tegra30 family"
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369 if SMP
-	select ARM_GIC
-	select CPU_V7
-	select PINCTRL
 	select PINCTRL_TEGRA30
 	select PL310_ERRATA_769419 if CACHE_L2X0
-	select USB_ARCH_HAS_EHCI if USB_SUPPORT
-	select USB_ULPI if USB_PHY
-	select USB_ULPI_VIEWPORT if USB_PHY
 	help
 	  Support for NVIDIA Tegra T30 processor family, based on the
 	  ARM CortexA9MP CPU and the ARM PL310 L2 cache controller
 
 config ARCH_TEGRA_114_SOC
 	bool "Enable support for Tegra114 family"
 	select HAVE_ARM_ARCH_TIMER
-	select ARM_GIC
+	select ARM_ERRATA_798181
 	select ARM_L1_CACHE_SHIFT_6
-	select CPU_V7
-	select PINCTRL
 	select PINCTRL_TEGRA114
 	help
 	  Support for NVIDIA Tegra T114 processor family, based on the
 	  ARM CortexA15MP CPU
 
-config TEGRA_PCI
-	bool "PCI Express support"
-	depends on ARCH_TEGRA_2x_SOC
-	select PCI
-
 config TEGRA_AHB
 	bool "Enable AHB driver for NVIDIA Tegra SoCs"
 	default y

arch/arm/mach-tegra/Makefile

@@ -17,24 +17,24 @@ obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= tegra20_speedo.o
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= tegra2_emc.o
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= sleep-tegra20.o
+obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= pm-tegra20.o
 ifeq ($(CONFIG_CPU_IDLE),y)
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= cpuidle-tegra20.o
 endif
 obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= tegra30_speedo.o
 obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= sleep-tegra30.o
+obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= pm-tegra30.o
 ifeq ($(CONFIG_CPU_IDLE),y)
 obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= cpuidle-tegra30.o
 endif
 obj-$(CONFIG_SMP)			+= platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)               += hotplug.o
-obj-$(CONFIG_TEGRA_PCI)			+= pcie.o
 
 obj-$(CONFIG_ARCH_TEGRA_114_SOC)	+= tegra114_speedo.o
 obj-$(CONFIG_ARCH_TEGRA_114_SOC)	+= sleep-tegra30.o
+obj-$(CONFIG_ARCH_TEGRA_114_SOC)	+= pm-tegra30.o
 ifeq ($(CONFIG_CPU_IDLE),y)
 obj-$(CONFIG_ARCH_TEGRA_114_SOC)	+= cpuidle-tegra114.o
 endif
 
-obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= board-harmony-pcie.o
-
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= board-paz00.o