Merge tag 'omap-devel-c-for-3.5' of git://git.kernel.org/pub/scm/linu…

…x/kernel/git/pjw/omap-pending into devel-hwmod-data

Some OMAP IP block data additions for 3.5, along with a
fix for a longstanding watchdog timer integration problem.

arch/arm/mach-omap2/Makefile

@@ -4,7 +4,7 @@
 
 # Common support
 obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \
-	 common.o gpio.o dma.o wd_timer.o display.o i2c.o
+	 common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o
 
 omap-2-3-common				= irq.o sdrc.o
 hwmod-common				= omap_hwmod.o \
@@ -189,6 +189,9 @@ ifneq ($(CONFIG_TIDSPBRIDGE),)
 obj-y					+= dsp.o
 endif
 
+# OMAP2420 MSDI controller integration support ("MMC")
+obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
+
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o

arch/arm/mach-omap2/hdq1w.c

@@ -0,0 +1,72 @@
+/*
+ * IP block integration code for the HDQ1W/1-wire IP block
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Paul Walmsley
+ *
+ * Based on the I2C reset code in arch/arm/mach-omap2/i2c.c by
+ *     Avinash.H.M <avinashhm@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#include <plat/omap_hwmod.h>
+#include <plat/hdq1w.h>
+
+#include "common.h"
+
+/* Maximum microseconds to wait for OMAP module to softreset */
+#define MAX_MODULE_SOFTRESET_WAIT	10000
+
+/**
+ * omap_hdq1w_reset - reset the OMAP HDQ1W module
+ * @oh: struct omap_hwmod *
+ *
+ * OCP soft reset the HDQ1W IP block.  Section 20.6.1.4 "HDQ1W/1-Wire
+ * Software Reset" of the OMAP34xx Technical Reference Manual Revision
+ * ZR (SWPU223R) does not include the rather important fact that, for
+ * the reset to succeed, the HDQ1W module's internal clock gate must be
+ * programmed to allow the clock to propagate to the rest of the
+ * module.  In this sense, it's rather similar to the I2C custom reset
+ * function.  Returns 0.
+ */
+int omap_hdq1w_reset(struct omap_hwmod *oh)
+{
+	u32 v;
+	int c = 0;
+
+	/* Write to the SOFTRESET bit */
+	omap_hwmod_softreset(oh);
+
+	/* Enable the module's internal clocks */
+	v = omap_hwmod_read(oh, HDQ_CTRL_STATUS_OFFSET);
+	v |= 1 << HDQ_CTRL_STATUS_CLOCKENABLE_SHIFT;
+	omap_hwmod_write(v, oh, HDQ_CTRL_STATUS_OFFSET);
+
+	/* Poll on RESETDONE bit */
+	omap_test_timeout((omap_hwmod_read(oh,
+					   oh->class->sysc->syss_offs)
+			   & SYSS_RESETDONE_MASK),
+			  MAX_MODULE_SOFTRESET_WAIT, c);
+
+	if (c == MAX_MODULE_SOFTRESET_WAIT)
+		pr_warning("%s: %s: softreset failed (waited %d usec)\n",
+			   __func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
+	else
+		pr_debug("%s: %s: softreset in %d usec\n", __func__,
+			 oh->name, c);
+
+	return 0;
+}

arch/arm/mach-omap2/io.c

@@ -363,24 +363,6 @@ static void __init omap_hwmod_init_postsetup(void)
 #endif
 	omap_hwmod_for_each(_set_hwmod_postsetup_state, &postsetup_state);
 
-	/*
-	 * Set the default postsetup state for unusual modules (like
-	 * MPU WDT).
-	 *
-	 * The postsetup_state is not actually used until
-	 * omap_hwmod_late_init(), so boards that desire full watchdog
-	 * coverage of kernel initialization can reprogram the
-	 * postsetup_state between the calls to
-	 * omap2_init_common_infra() and omap_sdrc_init().
-	 *
-	 * XXX ideally we could detect whether the MPU WDT was currently
-	 * enabled here and make this conditional
-	 */
-	postsetup_state = _HWMOD_STATE_DISABLED;
-	omap_hwmod_for_each_by_class("wd_timer",
-				     _set_hwmod_postsetup_state,
-				     &postsetup_state);
-
 	omap_pm_if_early_init();
 }
 

arch/arm/mach-omap2/msdi.c

@@ -0,0 +1,88 @@
+/*
+ * MSDI IP block reset
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ * XXX What about pad muxing?
+ */
+
+#include <linux/kernel.h>
+
+#include <plat/omap_hwmod.h>
+#include <plat/mmc.h>
+
+#include "common.h"
+
+/*
+ * MSDI_CON_OFFSET: offset in bytes of the MSDI IP block's CON register
+ *     from the IP block's base address
+ */
+#define MSDI_CON_OFFSET				0x0c
+
+/* Register bitfields in the CON register */
+#define MSDI_CON_POW_MASK			BIT(11)
+#define MSDI_CON_CLKD_MASK			(0x3f << 0)
+#define MSDI_CON_CLKD_SHIFT			0
+
+/* Maximum microseconds to wait for OMAP module to softreset */
+#define MAX_MODULE_SOFTRESET_WAIT	10000
+
+/* MSDI_TARGET_RESET_CLKD: clock divisor to use throughout the reset */
+#define MSDI_TARGET_RESET_CLKD		0x3ff
+
+/**
+ * omap_msdi_reset - reset the MSDI IP block
+ * @oh: struct omap_hwmod *
+ *
+ * The MSDI IP block on OMAP2420 has to have both the POW and CLKD
+ * fields set inside its CON register for a reset to complete
+ * successfully.  This is not documented in the TRM.  For CLKD, we use
+ * the value that results in the lowest possible clock rate, to attempt
+ * to avoid disturbing any cards.
+ */
+int omap_msdi_reset(struct omap_hwmod *oh)
+{
+	u16 v = 0;
+	int c = 0;
+
+	/* Write to the SOFTRESET bit */
+	omap_hwmod_softreset(oh);
+
+	/* Enable the MSDI core and internal clock */
+	v |= MSDI_CON_POW_MASK;
+	v |= MSDI_TARGET_RESET_CLKD << MSDI_CON_CLKD_SHIFT;
+	omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
+
+	/* Poll on RESETDONE bit */
+	omap_test_timeout((omap_hwmod_read(oh, oh->class->sysc->syss_offs)
+			   & SYSS_RESETDONE_MASK),
+			  MAX_MODULE_SOFTRESET_WAIT, c);
+
+	if (c == MAX_MODULE_SOFTRESET_WAIT)
+		pr_warning("%s: %s: softreset failed (waited %d usec)\n",
+			   __func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
+	else
+		pr_debug("%s: %s: softreset in %d usec\n", __func__,
+			 oh->name, c);
+
+	/* Disable the MSDI internal clock */
+	v &= ~MSDI_CON_CLKD_MASK;
+	omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
+
+	return 0;
+}

arch/arm/mach-omap2/omap_hwmod_2420_data.c

@@ -23,6 +23,7 @@
 #include <plat/dmtimer.h>
 #include <plat/l3_2xxx.h>
 #include <plat/l4_2xxx.h>
+#include <plat/mmc.h>
 
 #include "omap_hwmod_common_data.h"
 
@@ -239,6 +240,67 @@ static struct omap_hwmod omap2420_mcbsp2_hwmod = {
 	},
 };
 
+static struct omap_hwmod_class_sysconfig omap2420_msdi_sysc = {
+	.rev_offs	= 0x3c,
+	.sysc_offs	= 0x64,
+	.syss_offs	= 0x68,
+	.sysc_flags	= (SYSC_HAS_SOFTRESET | SYSS_HAS_RESET_STATUS),
+	.sysc_fields	= &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap2420_msdi_hwmod_class = {
+	.name	= "msdi",
+	.sysc	= &omap2420_msdi_sysc,
+	.reset	= &omap_msdi_reset,
+};
+
+/* msdi1 */
+static struct omap_hwmod_irq_info omap2420_msdi1_irqs[] = {
+	{ .irq = 83 },
+	{ .irq = -1 }
+};
+
+static struct omap_hwmod_dma_info omap2420_msdi1_sdma_reqs[] = {
+	{ .name = "tx", .dma_req = 61 }, /* OMAP24XX_DMA_MMC1_TX */
+	{ .name = "rx", .dma_req = 62 }, /* OMAP24XX_DMA_MMC1_RX */
+	{ .dma_req = -1 }
+};
+
+static struct omap_hwmod omap2420_msdi1_hwmod = {
+	.name		= "msdi1",
+	.class		= &omap2420_msdi_hwmod_class,
+	.mpu_irqs	= omap2420_msdi1_irqs,
+	.sdma_reqs	= omap2420_msdi1_sdma_reqs,
+	.main_clk	= "mmc_fck",
+	.prcm		= {
+		.omap2 = {
+			.prcm_reg_id = 1,
+			.module_bit = OMAP2420_EN_MMC_SHIFT,
+			.module_offs = CORE_MOD,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP2420_ST_MMC_SHIFT,
+		},
+	},
+	.flags		= HWMOD_16BIT_REG,
+};
+
+/* HDQ1W/1-wire */
+static struct omap_hwmod omap2420_hdq1w_hwmod = {
+	.name		= "hdq1w",
+	.mpu_irqs	= omap2_hdq1w_mpu_irqs,
+	.main_clk	= "hdq_fck",
+	.prcm		= {
+		.omap2 = {
+			.module_offs = CORE_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP24XX_EN_HDQ_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP24XX_ST_HDQ_SHIFT,
+		},
+	},
+	.class		= &omap2_hdq1w_class,
+};
+
 /*
  * interfaces
  */
@@ -428,6 +490,53 @@ static struct omap_hwmod_ocp_if omap2420_l4_core__mcbsp2 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+static struct omap_hwmod_addr_space omap2420_msdi1_addrs[] = {
+	{
+		.pa_start	= 0x4809c000,
+		.pa_end		= 0x4809c000 + SZ_128 - 1,
+		.flags		= ADDR_TYPE_RT,
+	},
+	{ }
+};
+
+/* l4_core -> msdi1 */
+static struct omap_hwmod_ocp_if omap2420_l4_core__msdi1 = {
+	.master		= &omap2xxx_l4_core_hwmod,
+	.slave		= &omap2420_msdi1_hwmod,
+	.clk		= "mmc_ick",
+	.addr		= omap2420_msdi1_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* l4_core -> hdq1w interface */
+static struct omap_hwmod_ocp_if omap2420_l4_core__hdq1w = {
+	.master		= &omap2xxx_l4_core_hwmod,
+	.slave		= &omap2420_hdq1w_hwmod,
+	.clk		= "hdq_ick",
+	.addr		= omap2_hdq1w_addr_space,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+	.flags		= OMAP_FIREWALL_L4 | OCPIF_SWSUP_IDLE,
+};
+
+
+/* l4_wkup -> 32ksync_counter */
+static struct omap_hwmod_addr_space omap2420_counter_32k_addrs[] = {
+	{
+		.pa_start	= 0x48004000,
+		.pa_end		= 0x4800401f,
+		.flags		= ADDR_TYPE_RT
+	},
+	{ }
+};
+
+static struct omap_hwmod_ocp_if omap2420_l4_wkup__counter_32k = {
+	.master		= &omap2xxx_l4_wkup_hwmod,
+	.slave		= &omap2xxx_counter_32k_hwmod,
+	.clk		= "sync_32k_ick",
+	.addr		= omap2420_counter_32k_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 static struct omap_hwmod_ocp_if *omap2420_hwmod_ocp_ifs[] __initdata = {
 	&omap2xxx_l3_main__l4_core,
 	&omap2xxx_mpu__l3_main,
@@ -468,6 +577,9 @@ static struct omap_hwmod_ocp_if *omap2420_hwmod_ocp_ifs[] __initdata = {
 	&omap2420_l4_core__mailbox,
 	&omap2420_l4_core__mcbsp1,
 	&omap2420_l4_core__mcbsp2,
+	&omap2420_l4_core__msdi1,
+	&omap2420_l4_core__hdq1w,
+	&omap2420_l4_wkup__counter_32k,
 	NULL,
 };