Merge branches 'pci/host-altera', 'pci/host-designware', 'pci/host-ge…

…neric', 'pci/host-imx6', 'pci/host-iproc', 'pci/host-mvebu', 'pci/host-rcar', 'pci/host-tegra' and 'pci/host-xgene' into next

* pci/host-altera:
  PCI: altera: Add Altera PCIe MSI driver
  PCI: altera: Add Altera PCIe host controller driver
  ARM: Add msi.h to Kbuild

* pci/host-designware:
  PCI: designware: Make "clocks" and "clock-names" optional DT properties
  PCI: designware: Make driver arch-agnostic
  ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
  PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
  Revert "PCI: designware: Program ATU with untranslated address"
  PCI: designware: Move calculation of bus addresses to DRA7xx
  PCI: designware: Make "num-lanes" an optional DT property
  PCI: designware: Require config accesses to be naturally aligned
  PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
  PCI: designware: Use exact access size in dw_pcie_cfg_read()
  PCI: spear: Fix dw_pcie_cfg_read/write() usage
  PCI: designware: Set up high part of MSI target address
  PCI: designware: Make get_msi_addr() return phys_addr_t, not u32
  PCI: designware: Implement multivector MSI IRQ setup
  PCI: designware: Factor out MSI msg setup
  PCI: Add msi_controller setup_irqs() method for special multivector setup
  PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK

* pci/host-generic:
  PCI: generic: Fix address window calculation for non-zero starting bus
  PCI: generic: Pass starting bus number to pci_scan_root_bus()
  PCI: generic: Allow multiple hosts with different map_bus() methods
  arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
  powerpc/PCI: Fix lookup of linux,pci-probe-only property
  PCI: generic: Fix lookup of linux,pci-probe-only property
  of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"

* pci/host-imx6:
  PCI: imx6: Add PCIE_PHY_RX_ASIC_OUT_VALID definition
  PCI: imx6: Return real error code from imx6_add_pcie_port()

* pci/host-iproc:
  PCI: iproc: Fix header comment "Corporation" misspelling
  PCI: iproc: Add outbound mapping support
  PCI: iproc: Update PCIe device tree bindings
  PCI: iproc: Improve link detection logic
  PCI: iproc: Fix PCIe reset logic
  PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM
  PCI: iproc: Remove unused struct iproc_pcie.irqs[]
  PCI: iproc: Fix code comment to match code

* pci/host-mvebu:
  PCI: mvebu: Remove code restricting accesses to slot 0
  PCI: mvebu: Add PCI Express root complex capability block
  PCI: mvebu: Improve clock/reset handling
  PCI: mvebu: Use gpio_desc to carry around gpio
  PCI: mvebu: Use devm_kcalloc() to allocate an array
  PCI: mvebu: Use gpio_set_value_cansleep()
  PCI: mvebu: Split port parsing and resource claiming from  port setup
  PCI: mvebu: Fix memory leaks and refcount leaks
  PCI: mvebu: Move port parsing and resource claiming to  separate function
  PCI: mvebu: Use port->name rather than "PCIe%d.%d"
  PCI: mvebu: Report full node name when reporting a DT error
  PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
  PCI: mvebu: Use of_get_available_child_count()
  PCI: mvebu: Use exact config access size; don't read/modify/write
  PCI: mvebu: Return zero for reserved or unimplemented config space

* pci/host-rcar:
  PCI: rcar: Fix I/O offset for multiple host bridges
  PCI: rcar: Set root bus nr to that provided in DT
  PCI: rcar: Remove dependency on ARM-specific struct hw_pci
  PCI: rcar: Make PCI aware of the I/O resources
  PCI: rcar: Build pcie-rcar.c only on ARM
  PCI: rcar: Build pci-rcar-gen2.c only on ARM

* pci/host-tegra:
  PCI: tegra: Wrap static pgprot_t initializer with __pgprot()

* pci/host-xgene:
  PCI/MSI: xgene: Remove msi_controller assignment

Documentation/devicetree/bindings/pci/altera-pcie-msi.txt

@@ -0,0 +1,28 @@
+* Altera PCIe MSI controller
+
+Required properties:
+- compatible:	should contain "altr,msi-1.0"
+- reg:		specifies the physical base address of the controller and
+		the length of the memory mapped region.
+- reg-names:	must include the following entries:
+		"csr": CSR registers
+		"vector_slave": vectors slave port region
+- interrupt-parent:	interrupt source phandle.
+- interrupts:	specifies the interrupt source of the parent interrupt
+		controller. The format of the interrupt specifier depends on the
+		parent interrupt controller.
+- num-vectors:	number of vectors, range 1 to 32.
+- msi-controller:	indicates that this is MSI controller node
+
+
+Example
+msi0: msi@0xFF200000 {
+	compatible = "altr,msi-1.0";
+	reg = <0xFF200000 0x00000010
+		0xFF200010 0x00000080>;
+	reg-names = "csr", "vector_slave";
+	interrupt-parent = <&hps_0_arm_gic_0>;
+	interrupts = <0 42 4>;
+	msi-controller;
+	num-vectors = <32>;
+};

Documentation/devicetree/bindings/pci/altera-pcie.txt

@@ -0,0 +1,49 @@
+* Altera PCIe controller
+
+Required properties:
+- compatible :	should contain "altr,pcie-root-port-1.0"
+- reg:		a list of physical base address and length for TXS and CRA.
+- reg-names:	must include the following entries:
+		"Txs": TX slave port region
+		"Cra": Control register access region
+- interrupt-parent:	interrupt source phandle.
+- interrupts:	specifies the interrupt source of the parent interrupt controller.
+		The format of the interrupt specifier depends on the parent interrupt
+		controller.
+- device_type:	must be "pci"
+- #address-cells:	set to <3>
+- #size-cells:	set to <2>
+- #interrupt-cells:	set to <1>
+- ranges:		describes the translation of addresses for root ports and standard
+		PCI regions.
+- interrupt-map-mask and interrupt-map: standard PCI properties to define the
+		mapping of the PCIe interface to interrupt numbers.
+
+Optional properties:
+- msi-parent:	Link to the hardware entity that serves as the MSI controller for this PCIe
+		controller.
+- bus-range:	PCI bus numbers covered
+
+Example
+	pcie_0: pcie@0xc00000000 {
+		compatible = "altr,pcie-root-port-1.0";
+		reg = <0xc0000000 0x20000000>,
+			<0xff220000 0x00004000>;
+		reg-names = "Txs", "Cra";
+		interrupt-parent = <&hps_0_arm_gic_0>;
+		interrupts = <0 40 4>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bus-range = <0x0 0xFF>;
+		device_type = "pci";
+		msi-parent = <&msi_to_gic_gen_0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_0 1>,
+			            <0 0 0 2 &pcie_0 2>,
+			            <0 0 0 3 &pcie_0 3>,
+			            <0 0 0 4 &pcie_0 4>;
+		ranges = <0x82000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x10000000
+			    0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>;
+	};

Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt

@@ -17,6 +17,21 @@ Optional properties:
 - phys: phandle of the PCIe PHY device
 - phy-names: must be "pcie-phy"
 
+- brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done
+by the ASIC after power on reset. In this case, SW needs to configure it
+
+If the brcm,pcie-ob property is present, the following properties become
+effective:
+
+Required:
+- brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal
+address used by the iProc PCIe core (not the PCIe address)
+- brcm,pcie-ob-window-size: The outbound address mapping window size (in MB)
+
+Optional:
+- brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to
+increase the outbound window size
+
 Example:
 	pcie0: pcie@18012000 {
 		compatible = "brcm,iproc-pcie";
@@ -38,6 +53,11 @@ Example:
 
 		phys = <&phy 0 5>;
 		phy-names = "pcie-phy";
+
+		brcm,pcie-ob;
+		brcm,pcie-ob-oarr-size;
+		brcm,pcie-ob-axi-offset = <0x00000000>;
+		brcm,pcie-ob-window-size = <256>;
 	};
 
 	pcie1: pcie@18013000 {

Documentation/devicetree/bindings/pci/designware-pcie.txt

@@ -15,14 +15,16 @@ Required properties:
 	to define the mapping of the PCIe interface to interrupt
 	numbers.
 - num-lanes: number of lanes to use
-- clocks: Must contain an entry for each entry in clock-names.
-	See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
-	- "pcie"
-	- "pcie_bus"
 
 Optional properties:
+- num-lanes: number of lanes to use (this property should be specified unless
+  the link is brought already up in BIOS)
 - reset-gpio: gpio pin number of power good signal
 - bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
   specify this property, to keep backwards compatibility a range of 0x00-0xff
   is assumed if not present)
+- clocks: Must contain an entry for each entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+	- "pcie"
+	- "pcie_bus"

Documentation/devicetree/bindings/pci/host-generic-pci.txt

@@ -34,8 +34,9 @@ Properties of the host controller node:
 - #size-cells    : Must be 2.
 
 - reg            : The Configuration Space base address and size, as accessed
-                   from the parent bus.
-
+                   from the parent bus.  The base address corresponds to
+                   the first bus in the "bus-range" property.  If no
+                   "bus-range" is specified, this will be bus 0 (the default).
 
 Properties of the /chosen node:
 

MAINTAINERS

@@ -7938,6 +7938,14 @@ F:	include/linux/pci*
 F:	arch/x86/pci/
 F:	arch/x86/kernel/quirks.c
 
+PCI DRIVER FOR ALTERA PCIE IP
+M:	Ley Foon Tan <lftan@altera.com>
+L:	rfi@lists.rocketboards.org (moderated for non-subscribers)
+L:	linux-pci@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/pci/altera-pcie.txt
+F:	drivers/pci/host/pcie-altera.c
+
 PCI DRIVER FOR ARM VERSATILE PLATFORM
 M:	Rob Herring <robh@kernel.org>
 L:	linux-pci@vger.kernel.org
@@ -8039,6 +8047,14 @@ L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/host/*spear*
 
+PCI MSI DRIVER FOR ALTERA MSI IP
+M:	Ley Foon Tan <lftan@altera.com>
+L:	rfi@lists.rocketboards.org (moderated for non-subscribers)
+L:	linux-pci@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/pci/altera-pcie-msi.txt
+F:	drivers/pci/host/pcie-altera-msi.c
+
 PCI MSI DRIVER FOR APPLIEDMICRO XGENE
 M:	Duc Dang <dhdang@apm.com>
 L:	linux-pci@vger.kernel.org

arch/arm/include/asm/Kbuild

@@ -14,6 +14,7 @@ generic-y += local.h
 generic-y += local64.h
 generic-y += mm-arch-hooks.h
 generic-y += msgbuf.h
+generic-y += msi.h
 generic-y += param.h
 generic-y += parport.h
 generic-y += poll.h

arch/arm/include/asm/mach/pci.h

@@ -52,12 +52,6 @@ struct pci_sys_data {
 	u8		(*swizzle)(struct pci_dev *, u8 *);
 					/* IRQ mapping				*/
 	int		(*map_irq)(const struct pci_dev *, u8, u8);
-					/* Resource alignement requirements	*/
-	resource_size_t (*align_resource)(struct pci_dev *dev,
-					  const struct resource *res,
-					  resource_size_t start,
-					  resource_size_t size,
-					  resource_size_t align);
 	void		*private_data;	/* platform controller private data	*/
 };
 

arch/arm/kernel/bios32.c

@@ -17,6 +17,11 @@
 #include <asm/mach/pci.h>
 
 static int debug_pci;
+static resource_size_t (*align_resource)(struct pci_dev *dev,
+		  const struct resource *res,
+		  resource_size_t start,
+		  resource_size_t size,
+		  resource_size_t align) = NULL;
 
 /*
  * We can't use pci_get_device() here since we are
@@ -456,7 +461,7 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		sys->busnr   = busnr;
 		sys->swizzle = hw->swizzle;
 		sys->map_irq = hw->map_irq;
-		sys->align_resource = hw->align_resource;
+		align_resource = hw->align_resource;
 		INIT_LIST_HEAD(&sys->resources);
 
 		if (hw->private_data)
@@ -572,16 +577,15 @@ resource_size_t pcibios_align_resource(void *data, const struct resource *res,
 				resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
-	struct pci_sys_data *sys = dev->sysdata;
 	resource_size_t start = res->start;
 
 	if (res->flags & IORESOURCE_IO && start & 0x300)
 		start = (start + 0x3ff) & ~0x3ff;
 
 	start = (start + align - 1) & ~(align - 1);
 
-	if (sys->align_resource)
-		return sys->align_resource(dev, res, start, size, align);
+	if (align_resource)
+		return align_resource(dev, res, start, size, align);
 
 	return start;
 }

arch/arm64/boot/dts/amd/amd-overdrive.dts

@@ -14,7 +14,6 @@
 
 	chosen {
 		stdout-path = &serial0;
-		linux,pci-probe-only;
 	};
 };
 

arch/powerpc/platforms/pseries/setup.c

@@ -40,6 +40,7 @@
 #include <linux/seq_file.h>
 #include <linux/root_dev.h>
 #include <linux/of.h>
+#include <linux/of_pci.h>
 #include <linux/kexec.h>
 
 #include <asm/mmu.h>
@@ -495,18 +496,7 @@ static void __init find_and_init_phbs(void)
 	 * PCI_PROBE_ONLY and PCI_REASSIGN_ALL_BUS can be set via properties
 	 * in chosen.
 	 */
-	if (of_chosen) {
-		const int *prop;
-
-		prop = of_get_property(of_chosen,
-				"linux,pci-probe-only", NULL);
-		if (prop) {
-			if (*prop)
-				pci_add_flags(PCI_PROBE_ONLY);
-			else
-				pci_clear_flags(PCI_PROBE_ONLY);
-		}
-	}
+	of_pci_check_probe_only();
 }
 
 static void __init pSeries_setup_arch(void)

drivers/of/of_pci.c

@@ -5,6 +5,7 @@
 #include <linux/of_device.h>
 #include <linux/of_pci.h>
 #include <linux/slab.h>
+#include <asm-generic/pci-bridge.h>
 
 static inline int __of_pci_pci_compare(struct device_node *node,
 				       unsigned int data)
@@ -117,6 +118,31 @@ int of_get_pci_domain_nr(struct device_node *node)
 }
 EXPORT_SYMBOL_GPL(of_get_pci_domain_nr);
 
+/**
+ * of_pci_check_probe_only - Setup probe only mode if linux,pci-probe-only
+ *                           is present and valid
+ */
+void of_pci_check_probe_only(void)
+{
+	u32 val;
+	int ret;
+
+	ret = of_property_read_u32(of_chosen, "linux,pci-probe-only", &val);
+	if (ret) {
+		if (ret == -ENODATA || ret == -EOVERFLOW)
+			pr_warn("linux,pci-probe-only without valid value, ignoring\n");
+		return;
+	}
+
+	if (val)
+		pci_add_flags(PCI_PROBE_ONLY);
+	else
+		pci_clear_flags(PCI_PROBE_ONLY);
+
+	pr_info("PCI: PROBE_ONLY %sabled\n", val ? "en" : "dis");
+}
+EXPORT_SYMBOL_GPL(of_pci_check_probe_only);
+
 /**
  * of_pci_dma_configure - Setup DMA configuration
  * @dev: ptr to pci_dev struct of the PCI device

drivers/pci/host/Kconfig

@@ -39,15 +39,17 @@ config PCI_TEGRA
 
 config PCI_RCAR_GEN2
 	bool "Renesas R-Car Gen2 Internal PCI controller"
-	depends on ARCH_SHMOBILE || (ARM && COMPILE_TEST)
+	depends on ARM
+	depends on ARCH_SHMOBILE || COMPILE_TEST
 	help
 	  Say Y here if you want internal PCI support on R-Car Gen2 SoC.
 	  There are 3 internal PCI controllers available with a single
 	  built-in EHCI/OHCI host controller present on each one.
 
 config PCI_RCAR_GEN2_PCIE
 	bool "Renesas R-Car PCIe controller"
-	depends on ARCH_SHMOBILE || (ARM && COMPILE_TEST)
+	depends on ARM
+	depends on ARCH_SHMOBILE || COMPILE_TEST
 	help
 	  Say Y here if you want PCIe controller support on R-Car Gen2 SoCs.
 
@@ -145,4 +147,21 @@ config PCIE_IPROC_BCMA
 	  Say Y here if you want to use the Broadcom iProc PCIe controller
 	  through the BCMA bus interface
 
+config PCIE_ALTERA
+	bool "Altera PCIe controller"
+	depends on ARM || NIOS2
+	depends on OF_PCI
+	select PCI_DOMAINS
+	help
+	  Say Y here if you want to enable PCIe controller support on Altera
+	  FPGA.
+
+config PCIE_ALTERA_MSI
+	bool "Altera PCIe MSI feature"
+	depends on PCIE_ALTERA && PCI_MSI
+	select PCI_MSI_IRQ_DOMAIN
+	help
+	  Say Y here if you want PCIe MSI support for the Altera FPGA.
+	  This MSI driver supports Altera MSI to GIC controller IP.
+
 endmenu

drivers/pci/host/Makefile

@@ -17,3 +17,5 @@ obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o
 obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o
 obj-$(CONFIG_PCIE_IPROC_PLATFORM) += pcie-iproc-platform.o
 obj-$(CONFIG_PCIE_IPROC_BCMA) += pcie-iproc-bcma.o
+obj-$(CONFIG_PCIE_ALTERA) += pcie-altera.o
+obj-$(CONFIG_PCIE_ALTERA_MSI) += pcie-altera-msi.o

drivers/pci/host/pci-dra7xx.c

@@ -62,6 +62,7 @@
 
 #define	PCIECTRL_DRA7XX_CONF_PHY_CS			0x010C
 #define	LINK_UP						BIT(16)
+#define	DRA7XX_CPU_TO_BUS_ADDR				0x0FFFFFFF
 
 struct dra7xx_pcie {
 	void __iomem		*base;
@@ -151,6 +152,12 @@ static void dra7xx_pcie_enable_interrupts(struct pcie_port *pp)
 static void dra7xx_pcie_host_init(struct pcie_port *pp)
 {
 	dw_pcie_setup_rc(pp);
+
+	pp->io_base &= DRA7XX_CPU_TO_BUS_ADDR;
+	pp->mem_base &= DRA7XX_CPU_TO_BUS_ADDR;
+	pp->cfg0_base &= DRA7XX_CPU_TO_BUS_ADDR;
+	pp->cfg1_base &= DRA7XX_CPU_TO_BUS_ADDR;
+
 	dra7xx_pcie_establish_link(pp);
 	if (IS_ENABLED(CONFIG_PCI_MSI))
 		dw_pcie_msi_init(pp);