mtd: spi-nor: spansion: add support for Cypress Semper flash

The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.

The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com

drivers/mtd/spi-nor/spansion.c

@@ -8,6 +8,172 @@
 
 #include "core.h"
 
+#define SPINOR_OP_RD_ANY_REG			0x65	/* Read any register */
+#define SPINOR_OP_WR_ANY_REG			0x71	/* Write any register */
+#define SPINOR_REG_CYPRESS_CFR2V		0x00800003
+#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24	0xb
+#define SPINOR_REG_CYPRESS_CFR3V		0x00800004
+#define SPINOR_REG_CYPRESS_CFR3V_PGSZ		BIT(4) /* Page size. */
+#define SPINOR_REG_CYPRESS_CFR5V		0x00800006
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN	0x3
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS	0
+#define SPINOR_OP_CYPRESS_RD_FAST		0xee
+
+/**
+ * spi_nor_cypress_octal_dtr_enable() - Enable octal DTR on Cypress flashes.
+ * @nor:		pointer to a 'struct spi_nor'
+ * @enable:              whether to enable or disable Octal DTR
+ *
+ * This also sets the memory access latency cycles to 24 to allow the flash to
+ * run at up to 200MHz.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_cypress_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	int ret;
+
+	if (enable) {
+		/* Use 24 dummy cycles for memory array reads. */
+		ret = spi_nor_write_enable(nor);
+		if (ret)
+			return ret;
+
+		*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24;
+		op = (struct spi_mem_op)
+			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+				   SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR2V,
+						   1),
+				   SPI_MEM_OP_NO_DUMMY,
+				   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+		ret = spi_mem_exec_op(nor->spimem, &op);
+		if (ret)
+			return ret;
+
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			return ret;
+
+		nor->read_dummy = 24;
+	}
+
+	/* Set/unset the octal and DTR enable bits. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	if (enable)
+		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
+	else
+		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS;
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(enable ? 3 : 4,
+					   SPINOR_REG_CYPRESS_CFR5V,
+					   1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	/* Read flash ID to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1),
+			   SPI_MEM_OP_ADDR(enable ? 4 : 0, 0, 1),
+			   SPI_MEM_OP_DUMMY(enable ? 3 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(round_up(nor->info->id_len, 2),
+					      buf, 1));
+
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (memcmp(buf, nor->info->id, nor->info->id_len))
+		return -EINVAL;
+
+	return 0;
+}
+
+static void s28hs512t_default_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_cypress_octal_dtr_enable;
+}
+
+static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/*
+	 * On older versions of the flash the xSPI Profile 1.0 table has the
+	 * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE.
+	 */
+	if (nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0)
+		nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode =
+			SPINOR_OP_CYPRESS_RD_FAST;
+
+	/* This flash is also missing the 4-byte Page Program opcode bit. */
+	spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP],
+				SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+	/*
+	 * Since xSPI Page Program opcode is backward compatible with
+	 * Legacy SPI, use Legacy SPI opcode there as well.
+	 */
+	spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP_8_8_8_DTR],
+				SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * The xSPI Profile 1.0 table advertises the number of additional
+	 * address bytes needed for Read Status Register command as 0 but the
+	 * actual value for that is 4.
+	 */
+	nor->params->rdsr_addr_nbytes = 4;
+}
+
+static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
+				     const struct sfdp_parameter_header *bfpt_header,
+				     const struct sfdp_bfpt *bfpt,
+				     struct spi_nor_flash_parameter *params)
+{
+	/*
+	 * The BFPT table advertises a 512B page size but the page size is
+	 * actually configurable (with the default being 256B). Read from
+	 * CFR3V[4] and set the correct size.
+	 */
+	struct spi_mem_op op =
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR3V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, nor->bouncebuf, 1));
+	int ret;
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (nor->bouncebuf[0] & SPINOR_REG_CYPRESS_CFR3V_PGSZ)
+		params->page_size = 512;
+	else
+		params->page_size = 256;
+
+	return 0;
+}
+
+static struct spi_nor_fixups s28hs512t_fixups = {
+	.default_init = s28hs512t_default_init,
+	.post_sfdp = s28hs512t_post_sfdp_fixup,
+	.post_bfpt = s28hs512t_post_bfpt_fixup,
+};
+
 static int
 s25fs_s_post_bfpt_fixups(struct spi_nor *nor,
 			 const struct sfdp_parameter_header *bfpt_header,
@@ -104,6 +270,11 @@ static const struct flash_info spansion_parts[] = {
 			     SPI_NOR_4B_OPCODES) },
 	{ "cy15x104q",  INFO6(0x042cc2, 0x7f7f7f, 512 * 1024, 1,
 			      SPI_NOR_NO_ERASE) },
+	{ "s28hs512t",   INFO(0x345b1a,      0, 256 * 1024, 256,
+			     SECT_4K | SPI_NOR_OCTAL_DTR_READ |
+			      SPI_NOR_OCTAL_DTR_PP)
+	  .fixups = &s28hs512t_fixups,
+	},
 };
 
 static void spansion_post_sfdp_fixups(struct spi_nor *nor)