Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Pull networking fixes from David Miller:
 "Just the usual assortment of small'ish fixes:

   1) Conntrack timeout is sometimes not initialized properly, from
      Alexander Potapenko.

   2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
      undefined behavior. From ZhangXiaoxu.

   3) des1 field of descriptor in stmmac driver is initialized with the
      wrong variable. From Yue Haibing.

   4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
      Schimmel.

   5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.

   6) Fallback refcount fix in TLS code, from Jakub Kicinski.

   7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.

   8) Fix recursive locking in team driver, from Hangbin Liu.

   9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.

  10) Don't use napi_alloc_frag() outside of softiq context of socionext
      driver, from Ilias Apalodimas.

  11) MAC address increment overflow in ncsi, from Tao Ren.

  12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.

  13) ipv4_link_failure has to validate the headers that are actually
      there because RAW sockets can pass in arbitrary garbage, from Eric
      Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  ipv4: add sanity checks in ipv4_link_failure()
  net/rose: fix unbound loop in rose_loopback_timer()
  rxrpc: fix race condition in rxrpc_input_packet()
  net: rds: exchange of 8K and 1M pool
  net: vrf: Fix operation not supported when set vrf mac
  net/ncsi: handle overflow when incrementing mac address
  net: socionext: replace napi_alloc_frag with the netdev variant on init
  net: atheros: fix spelling mistake "underun" -> "underrun"
  spi: ST ST95HF NFC: declare missing of table
  spi: Micrel eth switch: declare missing of table
  net: stmmac: move stmmac_check_ether_addr() to driver probe
  netfilter: fix nf_l4proto_log_invalid to log invalid packets
  netfilter: never get/set skb->tstamp
  netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
  Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
  dt-bindings: add an explanation for internal phy-mode
  net/tls: don't leak IV and record seq when offload fails
  net/tls: avoid potential deadlock in tls_set_device_offload_rx()
  selftests/net: correct the return value for run_afpackettests
  team: fix possible recursive locking when add slaves
  ...

Documentation/devicetree/bindings/net/davinci_emac.txt

@@ -20,6 +20,8 @@ Required properties:
 Optional properties:
 - phy-handle: See ethernet.txt file in the same directory.
               If absent, davinci_emac driver defaults to 100/FULL.
+- nvmem-cells: phandle, reference to an nvmem node for the MAC address
+- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
 - ti,davinci-rmii-en: 1 byte, 1 means use RMII
 - ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM?
 

Documentation/devicetree/bindings/net/ethernet.txt

@@ -10,15 +10,14 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt.
   the boot program; should be used in cases where the MAC address assigned to
   the device by the boot program is different from the "local-mac-address"
   property;
-- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
-- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used;
 - max-speed: number, specifies maximum speed in Mbit/s supported by the device;
 - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
   the maximum frame size (there's contradiction in the Devicetree
   Specification).
 - phy-mode: string, operation mode of the PHY interface. This is now a de-facto
   standard property; supported values are:
-  * "internal"
+  * "internal" (Internal means there is not a standard bus between the MAC and
+     the PHY, something proprietary is being used to embed the PHY in the MAC.)
   * "mii"
   * "gmii"
   * "sgmii"

Documentation/devicetree/bindings/net/macb.txt

@@ -26,6 +26,10 @@ Required properties:
 	Optional elements: 'tsu_clk'
 - clocks: Phandles to input clocks.
 
+Optional properties:
+- nvmem-cells: phandle, reference to an nvmem node for the MAC address
+- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
+
 Optional properties for PHY child node:
 - reset-gpios : Should specify the gpio for phy reset
 - magic-packet : If present, indicates that the hardware supports waking

Documentation/networking/decnet.txt

@@ -22,8 +22,6 @@ you'll need the following options as well...
     CONFIG_DECNET_ROUTER (to be able to add/delete routes)
     CONFIG_NETFILTER (will be required for the DECnet routing daemon)
 
-    CONFIG_DECNET_ROUTE_FWMARK is optional
-
 Don't turn on SIOCGIFCONF support for DECnet unless you are really sure
 that you need it, in general you won't and it can cause ifconfig to
 malfunction.

Documentation/networking/ip-sysctl.txt

@@ -422,6 +422,7 @@ tcp_min_rtt_wlen - INTEGER
 	minimum RTT when it is moved to a longer path (e.g., due to traffic
 	engineering). A longer window makes the filter more resistant to RTT
 	inflations such as transient congestion. The unit is seconds.
+	Possible values: 0 - 86400 (1 day)
 	Default: 300
 
 tcp_moderate_rcvbuf - BOOLEAN

drivers/atm/firestream.c

@@ -1646,7 +1646,7 @@ static irqreturn_t fs_irq (int irq, void *dev_id)
 	}
 
 	if (status & ISR_TBRQ_W) {
-		fs_dprintk (FS_DEBUG_IRQ, "Data tramsitted!\n");
+		fs_dprintk (FS_DEBUG_IRQ, "Data transmitted!\n");
 		process_txdone_queue (dev, &dev->tx_relq);
 	}
 

drivers/net/ethernet/atheros/atlx/atl1.c

@@ -1721,7 +1721,7 @@ static void atl1_inc_smb(struct atl1_adapter *adapter)
 	adapter->soft_stats.scc += smb->tx_1_col;
 	adapter->soft_stats.mcc += smb->tx_2_col;
 	adapter->soft_stats.latecol += smb->tx_late_col;
-	adapter->soft_stats.tx_underun += smb->tx_underrun;
+	adapter->soft_stats.tx_underrun += smb->tx_underrun;
 	adapter->soft_stats.tx_trunc += smb->tx_trunc;
 	adapter->soft_stats.tx_pause += smb->tx_pause;
 
@@ -3179,7 +3179,7 @@ static struct atl1_stats atl1_gstrings_stats[] = {
 	{"tx_deferred_ok", ATL1_STAT(soft_stats.deffer)},
 	{"tx_single_coll_ok", ATL1_STAT(soft_stats.scc)},
 	{"tx_multi_coll_ok", ATL1_STAT(soft_stats.mcc)},
-	{"tx_underun", ATL1_STAT(soft_stats.tx_underun)},
+	{"tx_underrun", ATL1_STAT(soft_stats.tx_underrun)},
 	{"tx_trunc", ATL1_STAT(soft_stats.tx_trunc)},
 	{"tx_pause", ATL1_STAT(soft_stats.tx_pause)},
 	{"rx_pause", ATL1_STAT(soft_stats.rx_pause)},

drivers/net/ethernet/atheros/atlx/atl1.h

@@ -681,7 +681,7 @@ struct atl1_sft_stats {
 	u64 scc;		/* packets TX after a single collision */
 	u64 mcc;		/* packets TX after multiple collisions */
 	u64 latecol;		/* TX packets w/ late collisions */
-	u64 tx_underun;		/* TX packets aborted due to TX FIFO underrun
+	u64 tx_underrun;	/* TX packets aborted due to TX FIFO underrun
 				 * or TRD FIFO underrun */
 	u64 tx_trunc;		/* TX packets truncated due to size > MTU */
 	u64 rx_pause;		/* num Pause packets received. */

drivers/net/ethernet/atheros/atlx/atl2.c

@@ -553,7 +553,7 @@ static void atl2_intr_tx(struct atl2_adapter *adapter)
 			netdev->stats.tx_aborted_errors++;
 		if (txs->late_col)
 			netdev->stats.tx_window_errors++;
-		if (txs->underun)
+		if (txs->underrun)
 			netdev->stats.tx_fifo_errors++;
 	} while (1);
 

drivers/net/ethernet/atheros/atlx/atl2.h

@@ -260,7 +260,7 @@ struct tx_pkt_status {
 	unsigned multi_col:1;
 	unsigned late_col:1;
 	unsigned abort_col:1;
-	unsigned underun:1;	/* current packet is aborted
+	unsigned underrun:1;	/* current packet is aborted
 				 * due to txram underrun */
 	unsigned:3;		/* reserved */
 	unsigned update:1;	/* always 1'b1 in tx_status_buf */

drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c

@@ -33,6 +33,26 @@
 #include <linux/bpf_trace.h>
 #include "en/xdp.h"
 
+int mlx5e_xdp_max_mtu(struct mlx5e_params *params)
+{
+	int hr = NET_IP_ALIGN + XDP_PACKET_HEADROOM;
+
+	/* Let S := SKB_DATA_ALIGN(sizeof(struct skb_shared_info)).
+	 * The condition checked in mlx5e_rx_is_linear_skb is:
+	 *   SKB_DATA_ALIGN(sw_mtu + hard_mtu + hr) + S <= PAGE_SIZE         (1)
+	 *   (Note that hw_mtu == sw_mtu + hard_mtu.)
+	 * What is returned from this function is:
+	 *   max_mtu = PAGE_SIZE - S - hr - hard_mtu                         (2)
+	 * After assigning sw_mtu := max_mtu, the left side of (1) turns to
+	 * SKB_DATA_ALIGN(PAGE_SIZE - S) + S, which is equal to PAGE_SIZE,
+	 * because both PAGE_SIZE and S are already aligned. Any number greater
+	 * than max_mtu would make the left side of (1) greater than PAGE_SIZE,
+	 * so max_mtu is the maximum MTU allowed.
+	 */
+
+	return MLX5E_HW2SW_MTU(params, SKB_MAX_HEAD(hr));
+}
+
 static inline bool
 mlx5e_xmit_xdp_buff(struct mlx5e_xdpsq *sq, struct mlx5e_dma_info *di,
 		    struct xdp_buff *xdp)
@@ -304,9 +324,9 @@ bool mlx5e_poll_xdpsq_cq(struct mlx5e_cq *cq, struct mlx5e_rq *rq)
 					mlx5e_xdpi_fifo_pop(xdpi_fifo);
 
 				if (is_redirect) {
-					xdp_return_frame(xdpi.xdpf);
 					dma_unmap_single(sq->pdev, xdpi.dma_addr,
 							 xdpi.xdpf->len, DMA_TO_DEVICE);
+					xdp_return_frame(xdpi.xdpf);
 				} else {
 					/* Recycle RX page */
 					mlx5e_page_release(rq, &xdpi.di, true);
@@ -345,9 +365,9 @@ void mlx5e_free_xdpsq_descs(struct mlx5e_xdpsq *sq, struct mlx5e_rq *rq)
 				mlx5e_xdpi_fifo_pop(xdpi_fifo);
 
 			if (is_redirect) {
-				xdp_return_frame(xdpi.xdpf);
 				dma_unmap_single(sq->pdev, xdpi.dma_addr,
 						 xdpi.xdpf->len, DMA_TO_DEVICE);
+				xdp_return_frame(xdpi.xdpf);
 			} else {
 				/* Recycle RX page */
 				mlx5e_page_release(rq, &xdpi.di, false);

drivers/net/ethernet/mellanox/mlx5/core/en/xdp.h

@@ -34,13 +34,12 @@
 
 #include "en.h"
 
-#define MLX5E_XDP_MAX_MTU ((int)(PAGE_SIZE - \
-				 MLX5_SKB_FRAG_SZ(XDP_PACKET_HEADROOM)))
 #define MLX5E_XDP_MIN_INLINE (ETH_HLEN + VLAN_HLEN)
 #define MLX5E_XDP_TX_EMPTY_DS_COUNT \
 	(sizeof(struct mlx5e_tx_wqe) / MLX5_SEND_WQE_DS)
 #define MLX5E_XDP_TX_DS_COUNT (MLX5E_XDP_TX_EMPTY_DS_COUNT + 1 /* SG DS */)
 
+int mlx5e_xdp_max_mtu(struct mlx5e_params *params);
 bool mlx5e_xdp_handle(struct mlx5e_rq *rq, struct mlx5e_dma_info *di,
 		      void *va, u16 *rx_headroom, u32 *len);
 bool mlx5e_poll_xdpsq_cq(struct mlx5e_cq *cq, struct mlx5e_rq *rq);

drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c

@@ -1586,7 +1586,7 @@ static int mlx5e_get_module_info(struct net_device *netdev,
 		break;
 	case MLX5_MODULE_ID_SFP:
 		modinfo->type       = ETH_MODULE_SFF_8472;
-		modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+		modinfo->eeprom_len = MLX5_EEPROM_PAGE_LENGTH;
 		break;
 	default:
 		netdev_err(priv->netdev, "%s: cable type not recognized:0x%x\n",

drivers/net/ethernet/mellanox/mlx5/core/en_main.c

@@ -3777,7 +3777,7 @@ int mlx5e_change_mtu(struct net_device *netdev, int new_mtu,
 	if (params->xdp_prog &&
 	    !mlx5e_rx_is_linear_skb(priv->mdev, &new_channels.params)) {
 		netdev_err(netdev, "MTU(%d) > %d is not allowed while XDP enabled\n",
-			   new_mtu, MLX5E_XDP_MAX_MTU);
+			   new_mtu, mlx5e_xdp_max_mtu(params));
 		err = -EINVAL;
 		goto out;
 	}
@@ -4212,7 +4212,8 @@ static int mlx5e_xdp_allowed(struct mlx5e_priv *priv, struct bpf_prog *prog)
 
 	if (!mlx5e_rx_is_linear_skb(priv->mdev, &new_channels.params)) {
 		netdev_warn(netdev, "XDP is not allowed with MTU(%d) > %d\n",
-			    new_channels.params.sw_mtu, MLX5E_XDP_MAX_MTU);
+			    new_channels.params.sw_mtu,
+			    mlx5e_xdp_max_mtu(&new_channels.params));
 		return -EINVAL;
 	}
 

drivers/net/ethernet/mellanox/mlx5/core/port.c

@@ -317,10 +317,6 @@ int mlx5_query_module_eeprom(struct mlx5_core_dev *dev,
 		size -= offset + size - MLX5_EEPROM_PAGE_LENGTH;
 
 	i2c_addr = MLX5_I2C_ADDR_LOW;
-	if (offset >= MLX5_EEPROM_PAGE_LENGTH) {
-		i2c_addr = MLX5_I2C_ADDR_HIGH;
-		offset -= MLX5_EEPROM_PAGE_LENGTH;
-	}
 
 	MLX5_SET(mcia_reg, in, l, 0);
 	MLX5_SET(mcia_reg, in, module, module_num);

drivers/net/ethernet/mellanox/mlxsw/pci_hw.h

@@ -27,7 +27,7 @@
 
 #define MLXSW_PCI_SW_RESET			0xF0010
 #define MLXSW_PCI_SW_RESET_RST_BIT		BIT(0)
-#define MLXSW_PCI_SW_RESET_TIMEOUT_MSECS	13000
+#define MLXSW_PCI_SW_RESET_TIMEOUT_MSECS	20000
 #define MLXSW_PCI_SW_RESET_WAIT_MSECS		100
 #define MLXSW_PCI_FW_READY			0xA1844
 #define MLXSW_PCI_FW_READY_MASK			0xFFFF

drivers/net/ethernet/mellanox/mlxsw/spectrum.c

@@ -3126,11 +3126,11 @@ mlxsw_sp_port_set_link_ksettings(struct net_device *dev,
 	if (err)
 		return err;
 
+	mlxsw_sp_port->link.autoneg = autoneg;
+
 	if (!netif_running(dev))
 		return 0;
 
-	mlxsw_sp_port->link.autoneg = autoneg;
-
 	mlxsw_sp_port_admin_status_set(mlxsw_sp_port, false);
 	mlxsw_sp_port_admin_status_set(mlxsw_sp_port, true);
 
@@ -3316,7 +3316,7 @@ static int mlxsw_sp_port_ets_init(struct mlxsw_sp_port *mlxsw_sp_port)
 		err = mlxsw_sp_port_ets_set(mlxsw_sp_port,
 					    MLXSW_REG_QEEC_HIERARCY_TC,
 					    i + 8, i,
-					    false, 0);
+					    true, 100);
 		if (err)
 			return err;
 	}

drivers/net/ethernet/netronome/nfp/abm/cls.c

@@ -39,7 +39,7 @@ nfp_abm_u32_check_knode(struct nfp_abm *abm, struct tc_cls_u32_knode *knode,
 	}
 	if (knode->sel->off || knode->sel->offshift || knode->sel->offmask ||
 	    knode->sel->offoff || knode->fshift) {
-		NL_SET_ERR_MSG_MOD(extack, "variable offseting not supported");
+		NL_SET_ERR_MSG_MOD(extack, "variable offsetting not supported");
 		return false;
 	}
 	if (knode->sel->hoff || knode->sel->hmask) {
@@ -78,7 +78,7 @@ nfp_abm_u32_check_knode(struct nfp_abm *abm, struct tc_cls_u32_knode *knode,
 
 	k = &knode->sel->keys[0];
 	if (k->offmask) {
-		NL_SET_ERR_MSG_MOD(extack, "offset mask - variable offseting not supported");
+		NL_SET_ERR_MSG_MOD(extack, "offset mask - variable offsetting not supported");
 		return false;
 	}
 	if (k->off) {

drivers/net/ethernet/socionext/netsec.c

@@ -673,7 +673,8 @@ static void netsec_process_tx(struct netsec_priv *priv)
 }
 
 static void *netsec_alloc_rx_data(struct netsec_priv *priv,
-				  dma_addr_t *dma_handle, u16 *desc_len)
+				  dma_addr_t *dma_handle, u16 *desc_len,
+				  bool napi)
 {
 	size_t total_len = SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 	size_t payload_len = NETSEC_RX_BUF_SZ;
@@ -682,7 +683,7 @@ static void *netsec_alloc_rx_data(struct netsec_priv *priv,
 
 	total_len += SKB_DATA_ALIGN(payload_len + NETSEC_SKB_PAD);
 
-	buf = napi_alloc_frag(total_len);
+	buf = napi ? napi_alloc_frag(total_len) : netdev_alloc_frag(total_len);
 	if (!buf)
 		return NULL;
 
@@ -765,7 +766,8 @@ static int netsec_process_rx(struct netsec_priv *priv, int budget)
 		/* allocate a fresh buffer and map it to the hardware.
 		 * This will eventually replace the old buffer in the hardware
 		 */
-		buf_addr = netsec_alloc_rx_data(priv, &dma_handle, &desc_len);
+		buf_addr = netsec_alloc_rx_data(priv, &dma_handle, &desc_len,
+						true);
 		if (unlikely(!buf_addr))
 			break;
 
@@ -1069,7 +1071,8 @@ static int netsec_setup_rx_dring(struct netsec_priv *priv)
 		void *buf;
 		u16 len;
 
-		buf = netsec_alloc_rx_data(priv, &dma_handle, &len);
+		buf = netsec_alloc_rx_data(priv, &dma_handle, &len,
+					   false);
 		if (!buf) {
 			netsec_uninit_pkt_dring(priv, NETSEC_RING_RX);
 			goto err_out;

drivers/net/ethernet/stmicro/stmmac/norm_desc.c

@@ -140,7 +140,7 @@ static void ndesc_init_rx_desc(struct dma_desc *p, int disable_rx_ic, int mode,
 	p->des0 |= cpu_to_le32(RDES0_OWN);
 
 	bfsize1 = min(bfsize, BUF_SIZE_2KiB - 1);
-	p->des1 |= cpu_to_le32(bfsize & RDES1_BUFFER1_SIZE_MASK);
+	p->des1 |= cpu_to_le32(bfsize1 & RDES1_BUFFER1_SIZE_MASK);
 
 	if (mode == STMMAC_CHAIN_MODE)
 		ndesc_rx_set_on_chain(p, end);

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -2616,8 +2616,6 @@ static int stmmac_open(struct net_device *dev)
 	u32 chan;
 	int ret;
 
-	stmmac_check_ether_addr(priv);
-
 	if (priv->hw->pcs != STMMAC_PCS_RGMII &&
 	    priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI) {
@@ -4303,6 +4301,8 @@ int stmmac_dvr_probe(struct device *device,
 	if (ret)
 		goto error_hw_init;
 
+	stmmac_check_ether_addr(priv);
+
 	/* Configure real RX and TX queues */
 	netif_set_real_num_rx_queues(ndev, priv->plat->rx_queues_to_use);
 	netif_set_real_num_tx_queues(ndev, priv->plat->tx_queues_to_use);

drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c

@@ -159,6 +159,12 @@ static const struct dmi_system_id quark_pci_dmi[] = {
 		},
 		.driver_data = (void *)&galileo_stmmac_dmi_data,
 	},
+	/*
+	 * There are 2 types of SIMATIC IOT2000: IOT20202 and IOT2040.
+	 * The asset tag "6ES7647-0AA00-0YA2" is only for IOT2020 which
+	 * has only one pci network device while other asset tags are
+	 * for IOT2040 which has two.
+	 */
 	{
 		.matches = {
 			DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"),
@@ -170,8 +176,6 @@ static const struct dmi_system_id quark_pci_dmi[] = {
 	{
 		.matches = {
 			DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"),
-			DMI_EXACT_MATCH(DMI_BOARD_ASSET_TAG,
-					"6ES7647-0AA00-1YA2"),
 		},
 		.driver_data = (void *)&iot2040_stmmac_dmi_data,
 	},

drivers/net/phy/spi_ks8995.c

@@ -159,6 +159,14 @@ static const struct spi_device_id ks8995_id[] = {
 };
 MODULE_DEVICE_TABLE(spi, ks8995_id);
 
+static const struct of_device_id ks8895_spi_of_match[] = {
+        { .compatible = "micrel,ks8995" },
+        { .compatible = "micrel,ksz8864" },
+        { .compatible = "micrel,ksz8795" },
+        { },
+ };
+MODULE_DEVICE_TABLE(of, ks8895_spi_of_match);
+
 static inline u8 get_chip_id(u8 val)
 {
 	return (val >> ID1_CHIPID_S) & ID1_CHIPID_M;
@@ -526,6 +534,7 @@ static int ks8995_remove(struct spi_device *spi)
 static struct spi_driver ks8995_driver = {
 	.driver = {
 		.name	    = "spi-ks8995",
+		.of_match_table = of_match_ptr(ks8895_spi_of_match),
 	},
 	.probe	  = ks8995_probe,
 	.remove	  = ks8995_remove,

drivers/net/team/team.c

@@ -1156,6 +1156,13 @@ static int team_port_add(struct team *team, struct net_device *port_dev,
 		return -EINVAL;
 	}
 
+	if (netdev_has_upper_dev(dev, port_dev)) {
+		NL_SET_ERR_MSG(extack, "Device is already an upper device of the team interface");
+		netdev_err(dev, "Device %s is already an upper device of the team interface\n",
+			   portname);
+		return -EBUSY;
+	}
+
 	if (port_dev->features & NETIF_F_VLAN_CHALLENGED &&
 	    vlan_uses_dev(dev)) {
 		NL_SET_ERR_MSG(extack, "Device is VLAN challenged and team device has VLAN set up");