Merge tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/…

…git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 5.2

  *) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
     that can be used to undo the operation performed in xlate
  *) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
     G12A SoC Family.
  *) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
     one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
  *) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
  *) Add new driver to support UFS M-PHY in MediaTek SoC
  *) Add new driver to support XUSB pad controller in Tegra186 SoCs
  *) Add new driver to support SERDES in TI's AM654 platform
  *) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
     to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
  *) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
  *) Add support for SERDES6G in phy-ocelot-serdes.c
  *) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
  *) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
  *) Add support to shut off regulators that power UFS during system suspend
  *) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
     channel which helps to enable/disable interrupts for each instance
     independently
  *) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
     PHY operates correctly over the entire temperature range.
  *) Use devm_clk_get_optional to get optional clocks instead of adding
     custom error checks

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

* tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (51 commits)
  dt-bindings: phy-qcom-qmp: Tweak qcom,msm8998-qmp-ufs-phy
  dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-pcie-phy
  phy: Add usb phy support for hi3660 Soc of Hisilicon
  dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
  scsi: phy: mediatek: fix typo in author's email address
  phy: ocelot-serdes: Add support for SERDES6G muxing
  phy: fsl-imx8mq-usb: add support for VBUS power control
  dt-bindings: phy-imx8mq-usb: add optional vbus supply regulator
  phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
  phy: ti: am654-serdes: Support all clksel values
  phy: ti: Add a new SERDES driver for TI's AM654x SoC
  dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
  phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
  phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
  phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
  phy: socionext: get optional clock by devm_clk_get_optional()
  phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
  phy: phy-mtk-tphy: get optional clock by devm_clk_get_optional()
  phy: renesas: rcar-gen3-usb2: enable/disable independent irqs
  phy: renesas: rcar-gen3-usb2: Use pdev's device pointer on dev_vdbg()
  ...

Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt

@@ -0,0 +1,32 @@
+Broadcom Stingray USB PHY
+
+Required properties:
+ - compatible : should be one of the listed compatibles
+	- "brcm,sr-usb-combo-phy" is combo PHY has two PHYs, one SS and one HS.
+	- "brcm,sr-usb-hs-phy" is a single HS PHY.
+ - reg: offset and length of the PHY blocks registers
+ - #phy-cells:
+   - Must be 1 for brcm,sr-usb-combo-phy as it expects one argument to indicate
+     the PHY number of two PHYs. 0 for HS PHY and 1 for SS PHY.
+   - Must be 0 for brcm,sr-usb-hs-phy.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+	usbphy0: usb-phy@0 {
+		compatible = "brcm,sr-usb-combo-phy";
+		reg = <0x00000000 0x100>;
+		#phy-cells = <1>;
+	};
+
+	usbphy1: usb-phy@10000 {
+		compatible = "brcm,sr-usb-combo-phy";
+		reg = <0x00010000 0x100>,
+		#phy-cells = <1>;
+	};
+
+	usbphy2: usb-phy@20000 {
+		compatible = "brcm,sr-usb-hs-phy";
+		reg = <0x00020000 0x100>,
+		#phy-cells = <0>;
+	};

Documentation/devicetree/bindings/phy/fsl,imx8mq-usb-phy.txt

@@ -7,6 +7,9 @@ Required properties:
 - clocks:	phandles to the clocks for each clock listed in clock-names
 - clock-names:	must contain "phy"
 
+Optional properties:
+- vbus-supply: A phandle to the regulator for USB VBUS.
+
 Example:
 	usb3_phy0: phy@381f0040 {
 		compatible = "fsl,imx8mq-usb-phy";

Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt

@@ -0,0 +1,22 @@
+* Amlogic G12A USB2 PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+- clocks:	a phandle to the clock of this PHY
+- clock-names:	must be "xtal"
+- resets:	a phandle to the reset line of this PHY
+- reset-names:	must be "phy"
+- phy-supply:	see phy-bindings.txt in this directory
+
+Example:
+	usb2_phy0: phy@36000 {
+		compatible = "amlogic,g12a-usb2-phy";
+		reg = <0x0 0x36000 0x0 0x2000>;
+		clocks = <&xtal>;
+		clock-names = "xtal";
+		resets = <&reset RESET_USB_PHY21>;
+		reset-names = "phy";
+		#phy-cells = <0>;
+	};

Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt

@@ -0,0 +1,22 @@
+* Amlogic G12A USB3 + PCIE Combo PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb3-pcie-phy"
+- #phys-cells:	must be 1. The cell number is used to select the phy mode
+  as defined in <dt-bindings/phy/phy.h> between PHY_TYPE_USB3 and PHY_TYPE_PCIE
+- reg:		The base address and length of the registers
+- clocks:	a phandle to the 100MHz reference clock of this PHY
+- clock-names:	must be "ref_clk"
+- resets:	phandle to the reset lines for the PHY control
+- reset-names:	must be "phy"
+
+Example:
+	usb3_pcie_phy: phy@46000 {
+		compatible = "amlogic,g12a-usb3-pcie-phy";
+		reg = <0x0 0x46000 0x0 0x2000>;
+		clocks = <&clkc CLKID_PCIE_PLL>;
+		clock-names = "ref_clk";
+		resets = <&reset RESET_PCIE_PHY>;
+		reset-names = "phy";
+		#phy-cells = <1>;
+	};

Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt

@@ -36,11 +36,20 @@ Required properties:
   - Tegra124: "nvidia,tegra124-xusb-padctl"
   - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
   - Tegra210: "nvidia,tegra210-xusb-padctl"
+  - Tegra186: "nvidia,tegra186-xusb-padctl"
 - reg: Physical base address and length of the controller's registers.
 - resets: Must contain an entry for each entry in reset-names.
 - reset-names: Must include the following entries:
   - "padctl"
 
+For Tegra186:
+- avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
+  power supply. Must supply 1.8 V.
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+  3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
+- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
+
 
 Pad nodes:
 ==========

Documentation/devicetree/bindings/phy/phy-hi3660-usb3.txt

@@ -0,0 +1,26 @@
+Hisilicon hi3660 USB PHY
+-----------------------
+
+Required properties:
+- compatible: should be "hisilicon,hi3660-usb-phy"
+- #phy-cells: must be 0
+- hisilicon,pericrg-syscon: phandle of syscon used to control phy.
+- hisilicon,pctrl-syscon: phandle of syscon used to control phy.
+- hisilicon,eye-diagram-param: parameter set for phy
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+This is a subnode of usb3_otg_bc register node.
+
+Example:
+	usb3_otg_bc: usb3_otg_bc@ff200000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0xff200000 0x0 0x1000>;
+
+		usb-phy {
+			compatible = "hisilicon,hi3660-usb-phy";
+			#phy-cells = <0>;
+			hisilicon,pericrg-syscon = <&crg_ctrl>;
+			hisilicon,pctrl-syscon = <&pctrl>;
+			hisilicon,eye-diagram-param = <0x22466e4>;
+		};
+	};

Documentation/devicetree/bindings/phy/phy-mtk-ufs.txt

@@ -0,0 +1,38 @@
+MediaTek Universal Flash Storage (UFS) M-PHY binding
+--------------------------------------------------------
+
+UFS M-PHY nodes are defined to describe on-chip UFS M-PHY hardware macro.
+Each UFS M-PHY node should have its own node.
+
+To bind UFS M-PHY with UFS host controller, the controller node should
+contain a phandle reference to UFS M-PHY node.
+
+Required properties for UFS M-PHY nodes:
+- compatible         : Compatible list, contains the following controller:
+                       "mediatek,mt8183-ufsphy" for ufs phy
+                       persent on MT81xx chipsets.
+- reg                : Address and length of the UFS M-PHY register set.
+- #phy-cells         : This property shall be set to 0.
+- clocks             : List of phandle and clock specifier pairs.
+- clock-names        : List of clock input name strings sorted in the same
+                       order as the clocks property. Following clocks are
+                       mandatory.
+                       "unipro": Unipro core control clock.
+                       "mp": M-PHY core control clock.
+
+Example:
+
+	ufsphy: phy@11fa0000 {
+		compatible = "mediatek,mt8183-ufsphy";
+		reg = <0 0x11fa0000 0 0xc000>;
+		#phy-cells = <0>;
+
+		clocks = <&infracfg_ao INFRACFG_AO_UNIPRO_SCK_CG>,
+			 <&infracfg_ao INFRACFG_AO_UFS_MP_SAP_BCLK_CG>;
+		clock-names = "unipro", "mp";
+	};
+
+	ufshci@11270000 {
+		...
+		phys = <&ufsphy>;
+	};

Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt

@@ -11,6 +11,7 @@ Required properties:
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
 	       "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
 	       "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
+	       "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
 	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
 	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
 	       "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845.
@@ -48,6 +49,8 @@ Required properties:
 			"aux", "cfg_ahb", "ref".
 		For "qcom,msm8998-qmp-ufs-phy" must contain:
 			"ref", "ref_aux".
+		For "qcom,msm8998-qmp-pcie-phy" must contain:
+			"aux", "cfg_ahb", "ref".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"aux", "cfg_ahb", "ref", "com_aux".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
@@ -59,7 +62,8 @@ Required properties:
 	   one for each entry in reset-names.
  - reset-names: "phy" for reset of phy block,
 		"common" for phy common block reset,
-		"cfg" for phy's ahb cfg block reset.
+		"cfg" for phy's ahb cfg block reset,
+		"ufsphy" for the PHY reset in the UFS controller.
 
 		For "qcom,ipq8074-qmp-pcie-phy" must contain:
 			"phy", "common".
@@ -69,12 +73,16 @@ Required properties:
 			"phy", "common".
 		For "qcom,msm8998-qmp-usb3-phy" must contain
 			"phy", "common".
-		For "qcom,msm8998-qmp-ufs-phy": no resets are listed.
+		For "qcom,msm8998-qmp-ufs-phy": must contain:
+			"ufsphy".
+		For "qcom,msm8998-qmp-pcie-phy" must contain:
+			"phy", "common".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"phy", "common".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
 			"phy", "common".
-		For "qcom,sdm845-qmp-ufs-phy": no resets are listed.
+		For "qcom,sdm845-qmp-ufs-phy": must contain:
+			"ufsphy".
 
  - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
  - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.

Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt

@@ -7,6 +7,7 @@ Required properties:
 - compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743 SoC.
 	      "renesas,usb-phy-r8a7744" if the device is a part of R8A7744 SoC.
 	      "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC.
+	      "renesas,usb-phy-r8a77470" if the device is a part of R8A77470 SoC.
 	      "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
 	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
 	      "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC.
@@ -30,7 +31,7 @@ channels. These subnodes must contain the following properties:
 - #phy-cells: see phy-bindings.txt in the same directory, must be <1>.
 
 The phandle's argument in the PHY specifier is the USB controller selector for
-the USB channel; see the selector meanings below:
+the USB channel other than r8a77470 SoC; see the selector meanings below:
 
 +-----------+---------------+---------------+
 |\ Selector |               |               |
@@ -41,22 +42,70 @@ the USB channel; see the selector meanings below:
 | 2         | PCI EHCI/OHCI | xHCI          |
 +-----------+---------------+---------------+
 
+For r8a77470 SoC;see the selector meaning below:
+
++-----------+---------------+---------------+
+|\ Selector |               |               |
++ --------- +       0       |       1       |
+| Channel  \|               |               |
++-----------+---------------+---------------+
+| 0         | EHCI/OHCI     | HS-USB        |
++-----------+---------------+---------------+
+
 Example (Lager board):
 
 	usb-phy@e6590100 {
 		compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy";
 		reg = <0 0xe6590100 0 0x100>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clocks = <&cpg CPG_MOD 704>;
 		clock-names = "usbhs";
+		power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+		resets = <&cpg 704>;
 
-		usb-channel@0 {
+		usb0: usb-channel@0 {
 			reg = <0>;
 			#phy-cells = <1>;
 		};
-		usb-channel@2 {
+		usb2: usb-channel@2 {
 			reg = <2>;
 			#phy-cells = <1>;
 		};
 	};
+
+Example (iWave RZ/G1C sbc):
+
+	usbphy0: usb-phy0@e6590100 {
+		compatible = "renesas,usb-phy-r8a77470",
+			     "renesas,rcar-gen2-usb-phy";
+		reg = <0 0xe6590100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&cpg CPG_MOD 704>;
+		clock-names = "usbhs";
+		power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
+		resets = <&cpg 704>;
+
+		usb0: usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+	};
+
+	usbphy1: usb-phy@e6598100 {
+		compatible = "renesas,usb-phy-r8a77470",
+			     "renesas,rcar-gen2-usb-phy";
+		reg = <0 0xe6598100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&cpg CPG_MOD 706>;
+		clock-names = "usbhs";
+		power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
+		resets = <&cpg 706>;
+
+		usb1: usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+	};

Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt

@@ -1,10 +1,12 @@
 * Renesas R-Car generation 3 USB 2.0 PHY
 
 This file provides information on what the device node for the R-Car generation
-3 and RZ/G2 USB 2.0 PHY contain.
+3, RZ/G1C and RZ/G2 USB 2.0 PHY contain.
 
 Required properties:
-- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
+- compatible: "renesas,usb2-phy-r8a77470" if the device is a part of an R8A77470
+	      SoC.
+	      "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
 	      SoC.
 	      "renesas,usb2-phy-r8a774c0" if the device is a part of an R8A774C0
 	      SoC.
@@ -27,7 +29,13 @@ Required properties:
 
 - reg: offset and length of the partial USB 2.0 Host register block.
 - clocks: clock phandle and specifier pair(s).
-- #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <1> (and
+	      using <0> is deprecated).
+
+The phandle's argument in the PHY specifier is the INT_STATUS bit of controller:
+- 1 = USBH_INTA (OHCI)
+- 2 = USBH_INTB (EHCI)
+- 3 = UCOM_INT (OTG and BC)
 
 Optional properties:
 To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are

Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt

@@ -7,12 +7,15 @@ Required properties:
  - reg: PHY register address offset and length in "general
    register files"
 
-Optional clocks using the clock bindings (see ../clock/clock-bindings.txt),
-specified by name:
+Optional properties:
  - clock-names: Should contain "emmcclk".  Although this is listed as optional
 		(because most boards can get basic functionality without having
 		access to it), it is strongly suggested.
+		See ../clock/clock-bindings.txt for details.
  - clocks: Should have a phandle to the card clock exported by the SDHCI driver.
+ - drive-impedance-ohm: Specifies the drive impedance in Ohm.
+                        Possible values are 33, 40, 50, 66 and 100.
+                        If not set, the default value of 50 will be applied.
 
 Example:
 
@@ -29,6 +32,7 @@ grf: syscon@ff770000 {
 		reg = <0xf780 0x20>;
 		clocks = <&sdhci>;
 		clock-names = "emmcclk";
+		drive-impedance-ohm = <50>;
 		#phy-cells = <0>;
 	};
 };