ARM: dts: Add device tree support for phycard pca100

Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".

Based on patches from:

Steffen Trumtrar <s.trumtrar@pengutronix.de>:
 - Original patch
 - ARM: dts: Set partition offsets for phycard
 - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions

Jan Luebbe <jlu@pengutronix.de>:
 - ARM: dts: Enable bad block table in NAND

Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/Makefile

@@ -112,6 +112,8 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx27-pdk.dtb \
 	imx27-phytec-phycore-som.dtb \
 	imx27-phytec-phycore-rdk.dtb \
+	imx27-phytec-phycard-s-som.dtb \
+	imx27-phytec-phycard-s-rdk.dtb \
 	imx31-bug.dtb \
 	imx51-apf51.dtb \
 	imx51-apf51dev.dtb \

arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts

@@ -0,0 +1,62 @@
+/*
+ * Copyright 2012 Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx27-phytec-phycard-s-som.dts"
+
+/ {
+	model = "Phytec pca100 rapid development kit";
+	compatible = "phytec,imx27-pca100-rdk", "phytec,imx27-pca100", "fsl,imx27";
+
+	display: display {
+		model = "Primeview-PD050VL1";
+		native-mode = <&timing0>;
+		bits-per-pixel = <16>;  /* non-standard but required */
+		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
+		display-timings {
+			timing0: 640x480 {
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <112>;
+				hfront-porch = <36>;
+				hsync-len = <32>;
+				vback-porch = <33>;
+				vfront-porch = <33>;
+				vsync-len = <2>;
+				clock-frequency = <25000000>;
+			};
+		};
+	};
+};
+
+&fb {
+	display = <&display>;
+	status = "okay";
+};
+
+&sdhci2 {
+	cd-gpios = <&gpio3 29 0>;
+	status = "okay";
+};
+
+&uart1 {
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	fsl,uart-has-rtscts;
+	status = "okay";
+};

arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts

@@ -0,0 +1,72 @@
+/*
+ * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
+ * and Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx27.dtsi"
+
+/ {
+	model = "Phytec pca100";
+	compatible = "phytec,imx27-pca100", "fsl,imx27";
+
+	memory {
+		reg = <0xa0000000 0x08000000>; /* 128MB */
+	};
+};
+
+&cspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio4 28 0>,
+		<&gpio4 27 0>;
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	ioexpander@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	lm75@4a {
+		compatible = "national,lm75";
+		reg = <0x4a>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	at24@52 {
+		compatible = "at,24c32";
+		pagesize = <32>;
+		reg = <0x52>;
+	};
+};
+
+&owire {
+	status = "okay";
+};