Merge tag 'omap-for-v4.8/soc-signed' of git://git.kernel.org/pub/scm/…

…linux/kernel/git/tmlind/linux-omap into next/soc

SoC related changes for omaps for v4.8 merge window:

- A series of DSS platform_data fixes to prepare for DSS driver changes
- Add tblck clck aliases for PWM
- A series of trivial spelling corrections
- Remove bogus eQEP, ePWM and eCAP hwmod entries
- A series of McBSP sidetone fixes
- Remove QSPI and DSS addresses from hwmod, these come from dts
- Fix RSTST register offset for pruss
- Make ti81xx_rtc_hwmod static
- Remove wrongly defined RSTST offset for PER Domain, note
  that the subject for this one wrongly has "dts" in the
  subject
- Add support for omap5 and dra7 workaround for 801819
- A series of patches to make kexec work for SMP omaps

* tag 'omap-for-v4.8/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (30 commits)
  ARM: OMAP2+: Fix build if CONFIG_SMP is not set
  ARM: OMAP4+: Allow kexec on SMP variants
  ARM: OMAP4+: Reset CPU1 properly for kexec
  ARM: OMAP4+: Prevent CPU1 related hang with kexec
  ARM: OMAP4+: Initialize SAR RAM base early for proper CPU1 reset for kexec
  ARM: dts: am43xx: Remove wrongly defined RSTST offset for PER Domain
  ARM: OMAP: make ti81xx_rtc_hwmod static
  ARM: AM43XX: hwmod: Fix RSTST register offset for pruss
  ARM: DRA7: hwmod: remove DSS addresses from hwmod
  ARM: DRA7: hwmod: Remove QSPI address space entry from hwmod
  ARM: OMAP2+: McBSP: Remove the old iclk allow/deny idle code
  ASoC: omap-mcbsp: sidetone: Use the new callback for iclk handling
  ASoC: omap-mcbsp: Rename omap_mcbsp_sysfs_remove() to omap_mcbsp_cleanup()
  ARM: OMAP3: pdata-quirks: Add support for McBSP2/3 sidetone handling
  ARM: OMAP3: McBSP: New callback for McBSP2/3 ICLK idle configuration
  ARM: OMAP3: hwmod data: Fix McBSP2/3 sidetone data
  ARM: AM335x/AM437x: hwmod: Remove eQEP, ePWM and eCAP hwmod entries
  ARM: OMAP2+: Fix typo in sdrc.h
  ARM: OMAP2+: Fix typo in omap_device.c
  ARM: OMAP2+: Fix typo in omap4-common.c
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/mach-omap1/ams-delta-fiq.c

@@ -136,7 +136,7 @@ void __init ams_delta_init_fiq(void)
 		fiq_buffer[i] = 0;
 
 	/*
-	 * FIQ mode r9 always points to the fiq_buffer, becauses the FIQ isr
+	 * FIQ mode r9 always points to the fiq_buffer, because the FIQ isr
 	 * will run in an unpredictable context. The fiq_buffer is the FIQ isr's
 	 * only means of communication with the IRQ level and other kernel
 	 * context code.

arch/arm/mach-omap1/include/mach/mtd-xip.h

@@ -39,7 +39,7 @@ static inline unsigned long xip_omap_mpu_timer_read(int nr)
 #define xip_currtime()		(~xip_omap_mpu_timer_read(0))
 
 /*
- * It's permitted to do approxmation for xip_elapsed_since macro
+ * It's permitted to do approximation for xip_elapsed_since macro
  * (see linux/mtd/xip.h)
  */
 

arch/arm/mach-omap2/Kconfig

@@ -240,4 +240,12 @@ endmenu
 
 endif
 
+config OMAP5_ERRATA_801819
+	bool "Errata 801819: An eviction from L1 data cache might stall indefinitely"
+	depends on SOC_OMAP5 || SOC_DRA7XX
+	help
+	  A livelock can occur in the L2 cache arbitration that might prevent
+	  a snoop from completing. Under certain conditions this can cause the
+	  system to deadlock.
+
 endmenu

arch/arm/mach-omap2/Makefile

@@ -8,7 +8,7 @@ ccflags-y := -I$(srctree)/$(src)/include \
 # Common support
 obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \
 	 common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o \
-	 omap_device.o sram.o drm.o
+	 omap_device.o omap-headsmp.o sram.o drm.o
 
 hwmod-common				= omap_hwmod.o omap_hwmod_reset.o \
 					  omap_hwmod_common_data.o
@@ -32,7 +32,7 @@ obj-$(CONFIG_SOC_HAS_OMAP2_SDRC)	+= sdrc.o
 
 # SMP support ONLY available for OMAP4
 
-smp-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
+smp-$(CONFIG_SMP)			+= omap-smp.o
 smp-$(CONFIG_HOTPLUG_CPU)		+= omap-hotplug.o
 omap-4-5-common				=  omap4-common.o omap-wakeupgen.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-common) $(smp-y) sleep44xx.o

arch/arm/mach-omap2/board-ldp.c

@@ -39,14 +39,15 @@
 #include "gpmc.h"
 #include "gpmc-smsc911x.h"
 
-#include <video/omapdss.h>
+#include <linux/platform_data/omapdss.h>
 #include <video/omap-panel-data.h>
 
 #include "board-flash.h"
 #include "mux.h"
 #include "hsmmc.h"
 #include "control.h"
 #include "common-board-devices.h"
+#include "display.h"
 
 #define LDP_SMSC911X_CS		1
 #define LDP_SMSC911X_GPIO	152

arch/arm/mach-omap2/board-rx51-video.c

@@ -15,13 +15,14 @@
 #include <linux/spi/spi.h>
 #include <linux/mm.h>
 #include <asm/mach-types.h>
-#include <video/omapdss.h>
+#include <linux/platform_data/omapdss.h>
 #include <video/omap-panel-data.h>
 
 #include <linux/platform_data/spi-omap2-mcspi.h>
 
 #include "soc.h"
 #include "board-rx51.h"
+#include "display.h"
 
 #include "mux.h"
 
@@ -32,7 +33,6 @@
 static struct connector_atv_platform_data rx51_tv_pdata = {
 	.name = "tv",
 	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
 	.invert_polarity = false,
 };
 

arch/arm/mach-omap2/cm3xxx.c

@@ -649,7 +649,7 @@ void omap3_cm_save_scratchpad_contents(u32 *ptr)
 	/*
 	 * As per erratum i671, ROM code does not respect the PER DPLL
 	 * programming scheme if CM_AUTOIDLE_PLL..AUTO_PERIPH_DPLL == 1.
-	 * Then,  in anycase, clear these bits to avoid extra latencies.
+	 * Then,  in any case, clear these bits to avoid extra latencies.
 	 */
 	*ptr++ = omap2_cm_read_mod_reg(PLL_MOD, CM_AUTOIDLE) &
 		~OMAP3430_AUTO_PERIPH_DPLL_MASK;

arch/arm/mach-omap2/common.h

@@ -257,18 +257,22 @@ extern void gic_dist_enable(void);
 extern bool gic_dist_disabled(void);
 extern void gic_timer_retrigger(void);
 extern void omap_smc1(u32 fn, u32 arg);
+extern void omap4_sar_ram_init(void);
 extern void __iomem *omap4_get_sar_ram_base(void);
+extern void omap4_mpuss_early_init(void);
 extern void omap_do_wfi(void);
 
-#ifdef CONFIG_SMP
-/* Needed for secondary core boot */
 extern void omap4_secondary_startup(void);
 extern void omap4460_secondary_startup(void);
+
+#ifdef CONFIG_SMP
+/* Needed for secondary core boot */
 extern u32 omap_modify_auxcoreboot0(u32 set_mask, u32 clear_mask);
 extern void omap_auxcoreboot_addr(u32 cpu_addr);
 extern u32 omap_read_auxcoreboot0(void);
 
 extern void omap4_cpu_die(unsigned int cpu);
+extern int omap4_cpu_kill(unsigned int cpu);
 
 extern const struct smp_operations omap4_smp_ops;
 

arch/arm/mach-omap2/display.c

@@ -29,7 +29,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 
-#include <video/omapdss.h>
+#include <linux/platform_data/omapdss.h>
 #include "omap_hwmod.h"
 #include "omap_device.h"
 #include "omap-pm.h"

arch/arm/mach-omap2/display.h

@@ -33,4 +33,9 @@ int omap_init_vout(void);
 
 struct device_node * __init omapdss_find_dss_of_node(void);
 
+struct omap_dss_board_info;
+
+/* Init with the board info */
+int omap_display_init(struct omap_dss_board_info *board_data);
+
 #endif

arch/arm/mach-omap2/dss-common.c

@@ -27,7 +27,7 @@
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 
-#include <video/omapdss.h>
+#include <linux/platform_data/omapdss.h>
 #include <video/omap-panel-data.h>
 
 #include "soc.h"

arch/arm/mach-omap2/io.c

@@ -690,6 +690,8 @@ void __init omap4430_init_early(void)
 	omap4xxx_check_revision();
 	omap4xxx_check_features();
 	omap2_prcm_base_init();
+	omap4_sar_ram_init();
+	omap4_mpuss_early_init();
 	omap4_pm_init_early();
 	omap44xx_voltagedomains_init();
 	omap44xx_powerdomains_init();
@@ -718,6 +720,7 @@ void __init omap5_init_early(void)
 	omap4_pm_init_early();
 	omap2_prcm_base_init();
 	omap5xxx_check_revision();
+	omap4_sar_ram_init();
 	omap54xx_voltagedomains_init();
 	omap54xx_powerdomains_init();
 	omap54xx_clockdomains_init();

arch/arm/mach-omap2/mcbsp.c

@@ -34,18 +34,24 @@
 #include "cm3xxx.h"
 #include "cm-regbits-34xx.h"
 
-static struct clk *mcbsp_iclks[5];
-
-static int omap3_enable_st_clock(unsigned int id, bool enable)
+static int omap3_mcbsp_force_ick_on(struct clk *clk, bool force_on)
 {
-	/*
-	 * Sidetone uses McBSP ICLK - which must not idle when sidetones
-	 * are enabled or sidetones start sounding ugly.
-	 */
-	if (enable)
-		return omap2_clk_deny_idle(mcbsp_iclks[id]);
+	if (!clk)
+		return 0;
+
+	if (force_on)
+		return omap2_clk_deny_idle(clk);
 	else
-		return omap2_clk_allow_idle(mcbsp_iclks[id]);
+		return omap2_clk_allow_idle(clk);
+}
+
+void __init omap3_mcbsp_init_pdata_callback(
+					struct omap_mcbsp_platform_data *pdata)
+{
+	if (!pdata)
+		return;
+
+	pdata->force_ick_on = omap3_mcbsp_force_ick_on;
 }
 
 static int __init omap_init_mcbsp(struct omap_hwmod *oh, void *unused)
@@ -55,7 +61,6 @@ static int __init omap_init_mcbsp(struct omap_hwmod *oh, void *unused)
 	struct omap_hwmod *oh_device[2];
 	struct omap_mcbsp_platform_data *pdata = NULL;
 	struct platform_device *pdev;
-	char clk_name[11];
 
 	sscanf(oh->name, "mcbsp%d", &id);
 
@@ -96,9 +101,7 @@ static int __init omap_init_mcbsp(struct omap_hwmod *oh, void *unused)
 	if (oh->dev_attr) {
 		oh_device[1] = omap_hwmod_lookup((
 		(struct omap_mcbsp_dev_attr *)(oh->dev_attr))->sidetone);
-		pdata->enable_st_clock = omap3_enable_st_clock;
-		sprintf(clk_name, "mcbsp%d_ick", id);
-		mcbsp_iclks[id] = clk_get(NULL, clk_name);
+		pdata->force_ick_on = omap3_mcbsp_force_ick_on;
 		count++;
 	}
 	pdev = omap_device_build_ss(name, id, oh_device, count, pdata,

arch/arm/mach-omap2/mux34xx.c

@@ -1266,7 +1266,7 @@ static struct omap_ball __initdata omap3_cus_ball[] = {
 #endif
 
 /*
- * Signals different on CBB package comapared to superset
+ * Signals different on CBB package compared to superset
  */
 #if defined(CONFIG_OMAP_MUX) && defined(CONFIG_OMAP_PACKAGE_CBB)
 static struct omap_mux __initdata omap3_cbb_subset[] = {
@@ -1597,7 +1597,7 @@ static struct omap_ball __initdata omap3_cbb_ball[] = {
 #endif
 
 /*
- * Signals different on 36XX CBP package comapared to 34XX CBC package
+ * Signals different on 36XX CBP package compared to 34XX CBC package
  */
 #if defined(CONFIG_OMAP_MUX) && defined(CONFIG_OMAP_PACKAGE_CBP)
 static struct omap_mux __initdata omap36xx_cbp_subset[] = {

arch/arm/mach-omap2/omap-headsmp.S

@@ -24,6 +24,16 @@
 #define AUX_CORE_BOOT0_PA			0x48281800
 #define API_HYP_ENTRY				0x102
 
+ENTRY(omap_secondary_startup)
+#ifdef CONFIG_SMP
+	b	secondary_startup
+#else
+/* Should never get here */
+again:	wfi
+	b	again
+#endif
+#ENDPROC(omap_secondary_startup)
+
 /*
  * OMAP5 specific entry point for secondary CPU to jump from ROM
  * code.  This routine also provides a holding flag into which
@@ -39,7 +49,7 @@ wait:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
 	and	r4, r4, #0x0f
 	cmp	r0, r4
 	bne	wait
-	b	secondary_startup
+	b	omap_secondary_startup
 ENDPROC(omap5_secondary_startup)
 /*
  * Same as omap5_secondary_startup except we call into the ROM to
@@ -59,7 +69,7 @@ wait_2:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
 	adr	r0, hyp_boot
 	smc	#0
 hyp_boot:
-	b	secondary_startup
+	b	omap_secondary_startup
 ENDPROC(omap5_secondary_hyp_startup)
 /*
  * OMAP4 specific entry point for secondary CPU to jump from ROM
@@ -82,7 +92,7 @@ hold:	ldr	r12,=0x103
 	 * we've been released from the wait loop,secondary_stack
 	 * should now contain the SVC stack for this core
 	 */
-	b	secondary_startup
+	b	omap_secondary_startup
 ENDPROC(omap4_secondary_startup)
 
 ENTRY(omap4460_secondary_startup)
@@ -119,5 +129,5 @@ hold_2:	ldr	r12,=0x103
 	 * we've been released from the wait loop,secondary_stack
 	 * should now contain the SVC stack for this core
 	 */
-	b	secondary_startup
+	b	omap_secondary_startup
 ENDPROC(omap4460_secondary_startup)

arch/arm/mach-omap2/omap-hotplug.c

@@ -64,3 +64,9 @@ void omap4_cpu_die(unsigned int cpu)
 		pr_debug("CPU%u: spurious wakeup call\n", cpu);
 	}
 }
+
+/* Needed by kexec and platform_can_cpu_hotplug() */
+int omap4_cpu_kill(unsigned int cpu)
+{
+	return 1;
+}

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -62,6 +62,8 @@
 #include "prm44xx.h"
 #include "prm-regbits-44xx.h"
 
+static void __iomem *sar_base;
+
 #ifdef CONFIG_SMP
 
 struct omap4_cpu_pm_info {
@@ -90,7 +92,6 @@ struct cpu_pm_ops {
 
 static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
 static struct powerdomain *mpuss_pd;
-static void __iomem *sar_base;
 static u32 cpu_context_offset;
 
 static int default_finish_suspend(unsigned long cpu_state)
@@ -366,9 +367,6 @@ int __init omap4_mpuss_init(void)
 		return -ENODEV;
 	}
 
-	if (cpu_is_omap44xx())
-		sar_base = omap4_get_sar_ram_base();
-
 	/* Initilaise per CPU PM information */
 	pm_info = &per_cpu(omap4_pm_info, 0x0);
 	if (sar_base) {
@@ -444,3 +442,26 @@ int __init omap4_mpuss_init(void)
 }
 
 #endif
+
+/*
+ * For kexec, we must set CPU1_WAKEUP_NS_PA_ADDR to point to
+ * current kernel's secondary_startup() early before
+ * clockdomains_init(). Otherwise clockdomain_init() can
+ * wake CPU1 and cause a hang.
+ */
+void __init omap4_mpuss_early_init(void)
+{
+	unsigned long startup_pa;
+
+	if (!cpu_is_omap44xx())
+		return;
+
+	sar_base = omap4_get_sar_ram_base();
+
+	if (cpu_is_omap443x())
+		startup_pa = virt_to_phys(omap4_secondary_startup);
+	else
+		startup_pa = virt_to_phys(omap4460_secondary_startup);
+
+	writel_relaxed(startup_pa, sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
+}

arch/arm/mach-omap2/omap-secure.h

@@ -46,6 +46,7 @@
 
 #define OMAP5_DRA7_MON_SET_CNTFRQ_INDEX	0x109
 #define OMAP5_MON_AMBA_IF_INDEX		0x108
+#define OMAP5_DRA7_MON_SET_ACR_INDEX	0x107
 
 /* Secure PPA(Primary Protected Application) APIs */
 #define OMAP4_PPA_L2_POR_INDEX		0x23