bnxt_en: Set NPAR 1.2 support when registering with firmware

NPAR (Network interface card partitioning)[1] 1.2 adds a transparent
VLAN tag for all packets between the NIC and the switch.  Because of
that, RX VLAN acceleration cannot be supported for any additional
host configured VLANs.  The driver has to acknowledge that it can
support no RX VLAN acceleration and set the NPAR 1.2 supported flag
when registering with the FW.  Otherwise, the FW call will fail and
the driver will abort on these NPAR 1.2 NICs with this error:

bnxt_en 0000:26:00.0 (unnamed net_device) (uninitialized): hwrm req_type 0x1d seq id 0xb error 0x2

[1] https://techdocs.broadcom.com/us/en/storage-and-ethernet-connectivity/ethernet-nic-controllers/bcm957xxx/adapters/introduction/features/network-partitioning-npar.html

Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250213011240.1640031-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/broadcom/bnxt/bnxt.c

@@ -5565,6 +5565,8 @@ int bnxt_hwrm_func_drv_rgtr(struct bnxt *bp, unsigned long *bmap, int bmap_size,
 	if (bp->fw_cap & BNXT_FW_CAP_ERROR_RECOVERY)
 		flags |= FUNC_DRV_RGTR_REQ_FLAGS_ERROR_RECOVERY_SUPPORT |
 			 FUNC_DRV_RGTR_REQ_FLAGS_MASTER_SUPPORT;
+	if (bp->fw_cap & BNXT_FW_CAP_NPAR_1_2)
+		flags |= FUNC_DRV_RGTR_REQ_FLAGS_NPAR_1_2_SUPPORT;
 	req->flags = cpu_to_le32(flags);
 	req->ver_maj_8b = DRV_VER_MAJ;
 	req->ver_min_8b = DRV_VER_MIN;
@@ -8365,6 +8367,7 @@ static int bnxt_hwrm_func_qcfg(struct bnxt *bp)
 
 	switch (resp->port_partition_type) {
 	case FUNC_QCFG_RESP_PORT_PARTITION_TYPE_NPAR1_0:
+	case FUNC_QCFG_RESP_PORT_PARTITION_TYPE_NPAR1_2:
 	case FUNC_QCFG_RESP_PORT_PARTITION_TYPE_NPAR1_5:
 	case FUNC_QCFG_RESP_PORT_PARTITION_TYPE_NPAR2_0:
 		bp->port_partition_type = resp->port_partition_type;
@@ -9529,6 +9532,8 @@ static int __bnxt_hwrm_func_qcaps(struct bnxt *bp)
 		bp->fw_cap |= BNXT_FW_CAP_HOT_RESET_IF;
 	if (BNXT_PF(bp) && (flags_ext & FUNC_QCAPS_RESP_FLAGS_EXT_FW_LIVEPATCH_SUPPORTED))
 		bp->fw_cap |= BNXT_FW_CAP_LIVEPATCH;
+	if (flags_ext & FUNC_QCAPS_RESP_FLAGS_EXT_NPAR_1_2_SUPPORTED)
+		bp->fw_cap |= BNXT_FW_CAP_NPAR_1_2;
 	if (BNXT_PF(bp) && (flags_ext & FUNC_QCAPS_RESP_FLAGS_EXT_DFLT_VLAN_TPID_PCP_SUPPORTED))
 		bp->fw_cap |= BNXT_FW_CAP_DFLT_VLAN_TPID_PCP;
 	if (flags_ext & FUNC_QCAPS_RESP_FLAGS_EXT_BS_V2_SUPPORTED)

drivers/net/ethernet/broadcom/bnxt/bnxt.h

@@ -2492,6 +2492,7 @@ struct bnxt {
 	#define BNXT_FW_CAP_CFA_RFS_RING_TBL_IDX_V3	BIT_ULL(39)
 	#define BNXT_FW_CAP_VNIC_RE_FLUSH		BIT_ULL(40)
 	#define BNXT_FW_CAP_SW_MAX_RESOURCE_LIMITS	BIT_ULL(41)
+	#define BNXT_FW_CAP_NPAR_1_2			BIT_ULL(42)
 
 	u32			fw_dbg_cap;