Merge tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v5.11 kernel.

  Drivers, drivers and drivers. Not a single core change.

  Some new stuff, especially a bunch of new Intel, Qualcomm and Ocelot
  SoCs.

  As part of the modularization attempt, I applied one patch affecting
  the firmware subsystem as a functional (not syntactic/semantic)
  dependency and then it blew up in our face, so I had to revert it,
  bummer. It will come in later, through that subsystem, I guess.

  New drivers:

   - New driver for the Microchip Serial GPIO "SGPIO".

   - Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.

  New subdrivers:

   - Intel Lakefield subdriver.

   - Intel Elkhart Lake subdriver.

   - Intel Alder Lake-S subdriver.

   - Qualcomm MSM8953 subdriver.

   - Qualcomm SDX55 subdriver.

   - Qualcomm SDX55 PMIC subdriver.

   - Ocelot Luton SoC subdriver.

   - Ocelot Serval SoC subdriver.

  Modularization:

   - The Meson driver can now be built as modules.

   - The Qualcomm driver(s) can now be built as modules.

  Incremental improvements:

   - The Intel driver now supports pin configuration for GPIO-related
     configurations.

   - A bunch of Renesas PFC drivers have been augmented with support for
     QSPI pins, groups and functions.

   - Non-critical fixes to the irq handling in the Allwinner Sunxi
     driver"

* tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
  pinctrl/spear: simplify the return expression of spear300_pinctrl_probe()
  pinctrl: mediatek: simplify the return expression of mtk_pinconf_bias_disable_set_rev1()
  dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add irq support
  pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)
  pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver
  dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings
  pinctrl: qcom-pmic-gpio: Add support for pmx55
  dt-bindings: pinctrl: qcom-pmic-gpio: Add pmx55 support
  pinctrl: pinctrl-microchip-sgpio: Mark some symbols with static keyword
  pinctrl: at91-pio4: Make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix build error
  pinctrl: mtk: Fix low level output voltage issue
  pinctrl: falcon: add missing put_device() call in pinctrl_falcon_probe()
  pinctrl: actions: pinctrl-s500: Constify s500_padinfo[]
  pinctrl: pinctrl-microchip-sgpio: Add OF config dependency
  pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO
  dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
  pinctrl: at91-pio4: add support for fewer lines on last PIO bank
  pinctrl: sunxi: Always call chained_irq_{enter, exit} in sunxi_pinctrl_irq_handler
  pinctrl: sunxi: Mark the irq bank not found in sunxi_pinctrl_irq_handler() with WARN_ON
  pinctrl: sunxi: fix irq bank map for the Allwinner A100 pin controller
  ...

Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml

@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microsemi/Microchip Serial GPIO controller
+
+maintainers:
+  - Lars Povlsen <lars.povlsen@microchip.com>
+
+description: |
+  By using a serial interface, the SIO controller significantly extend
+  the number of available GPIOs with a minimum number of additional
+  pins on the device. The primary purpose of the SIO controllers is to
+  connect control signals from SFP modules and to act as an LED
+  controller.
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - microchip,sparx5-sgpio
+      - mscc,ocelot-sgpio
+      - mscc,luton-sgpio
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  microchip,sgpio-port-ranges:
+    description: This is a sequence of tuples, defining intervals of
+      enabled ports in the serial input stream. The enabled ports must
+      match the hardware configuration in order for signals to be
+      properly written/read to/from the controller holding
+      registers. Being tuples, then number of arguments must be
+      even. The tuples mast be ordered (low, high) and are
+      inclusive.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description: |
+            "low" indicates start bit number of range
+          minimum: 0
+          maximum: 31
+        - description: |
+            "high" indicates end bit number of range
+          minimum: 0
+          maximum: 31
+    minItems: 1
+    maxItems: 32
+
+  bus-frequency:
+    description: The sgpio controller frequency (Hz). This dictates
+      the serial bitstream speed, which again affects the latency in
+      getting control signals back and forth between external shift
+      registers. The speed must be no larger than half the system
+      clock, and larger than zero.
+    default: 12500000
+
+patternProperties:
+  "^gpio@[0-1]$":
+    type: object
+    properties:
+      compatible:
+        const: microchip,sparx5-sgpio-bank
+
+      reg:
+        description: |
+          The GPIO bank number. "0" is designates the input pin bank,
+          "1" the output bank.
+        maxItems: 1
+
+      gpio-controller: true
+
+      '#gpio-cells':
+        description: |
+         Specifies the pin (port and bit) and flags. Note that the
+         SGIO pin is defined by *2* numbers, a port number between 0
+         and 31, and a bit index, 0 to 3. The maximum bit number is
+         controlled indirectly by the "ngpios" property: (ngpios/32).
+        const: 3
+
+      interrupts:
+        description: Specifies the sgpio IRQ (in parent controller)
+        maxItems: 1
+
+      interrupt-controller: true
+
+      '#interrupt-cells':
+        description:
+         Specifies the pin (port and bit) and flags, as defined in
+         defined in include/dt-bindings/interrupt-controller/irq.h
+        const: 3
+
+      ngpios:
+        description: The numbers of GPIO's exposed. This must be a
+          multiple of 32.
+        minimum: 32
+        maximum: 128
+
+    required:
+      - compatible
+      - reg
+      - gpio-controller
+      - '#gpio-cells'
+      - ngpios
+
+    additionalProperties: false
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - microchip,sgpio-port-ranges
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    sgpio2: gpio@1101059c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "microchip,sparx5-sgpio";
+      clocks = <&sys_clk>;
+      pinctrl-0 = <&sgpio2_pins>;
+      pinctrl-names = "default";
+      reg = <0x1101059c 0x100>;
+      microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+      bus-frequency = <25000000>;
+      sgpio_in2: gpio@0 {
+        reg = <0>;
+        compatible = "microchip,sparx5-sgpio-bank";
+        gpio-controller;
+        #gpio-cells = <3>;
+        ngpios = <96>;
+        interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-controller;
+        #interrupt-cells = <3>;
+      };
+      sgpio_out2: gpio@1 {
+        compatible = "microchip,sparx5-sgpio-bank";
+        reg = <1>;
+        gpio-controller;
+        #gpio-cells = <3>;
+        ngpios = <96>;
+      };
+    };

Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt

@@ -3,7 +3,8 @@ Microsemi Ocelot pin controller Device Tree Bindings
 
 Required properties:
  - compatible		: Should be "mscc,ocelot-pinctrl",
-			  "mscc,jaguar2-pinctrl" or "microchip,sparx5-pinctrl"
+			  "mscc,jaguar2-pinctrl", "microchip,sparx5-pinctrl",
+			  "mscc,luton-pinctrl" or "mscc,serval-pinctrl"
  - reg			: Address and length of the register set for the device
  - gpio-controller	: Indicates this device is a GPIO controller
  - #gpio-cells		: Must be 2.

Documentation/devicetree/bindings/pinctrl/qcom,lpass-lpi-pinctrl.yaml

@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,lpass-lpi-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS)
+  Low Power Island (LPI) TLMM block
+
+maintainers:
+  - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
+
+description: |
+  This binding describes the Top Level Mode Multiplexer block found in the
+  LPASS LPI IP on most Qualcomm SoCs
+
+properties:
+  compatible:
+    const: qcom,sm8250-lpass-lpi-pinctrl
+
+  reg:
+    minItems: 2
+    maxItems: 2
+
+  clocks:
+    items:
+      - description: LPASS Core voting clock
+      - description: LPASS Audio voting clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: audio
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description: Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+
+  gpio-ranges:
+    maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-9][0-9])$"
+        minItems: 1
+        maxItems: 14
+
+      function:
+        enum: [ gpio, swr_tx_clk, qua_mi2s_sclk, swr_tx_data, qua_mi2s_ws,
+                qua_mi2s_data, swr_rx_clk, swr_rx_data, dmic1_clk, i2s1_clk,
+                dmic1_data, i2s1_ws, dmic2_clk, dmic2_data, i2s1_data,
+                i2s2_clk, wsa_swr_clk, i2s2_ws, wsa_swr_data, dmic3_clk,
+                dmic3_data, i2s2_data ]
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+
+      drive-strength:
+        enum: [2, 4, 6, 8, 10, 12, 14, 16]
+        default: 2
+        description:
+          Selects the drive strength for the specified pins, in mA.
+
+      slew-rate:
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+            0: No adjustments
+            1: Higher Slew rate (faster edges)
+            2: Lower Slew rate (slower edges)
+            3: Reserved (No adjustments)
+
+      bias-pull-down: true
+
+      bias-pull-up: true
+
+      bias-disable: true
+
+      output-high: true
+
+      output-low: true
+
+    required:
+      - pins
+      - function
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/sound/qcom,q6afe.h>
+    lpi_tlmm: pinctrl@33c0000 {
+        compatible = "qcom,sm8250-lpass-lpi-pinctrl";
+        reg = <0x33c0000 0x20000>,
+              <0x3550000 0x10000>;
+        clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+                 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+        clock-names = "core", "audio";
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&lpi_tlmm 0 0 14>;
+    };