ARM64: dts: marvell: Fix some common switch mistakes

Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts

@@ -126,32 +126,32 @@
 
 	reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
 
-	ports {
-		switch0port1: port@1 {
+	ethernet-ports {
+		switch0port1: ethernet-port@1 {
 			reg = <1>;
 			label = "lan0";
 			phy-handle = <&switch0phy0>;
 		};
 
-		switch0port2: port@2 {
+		switch0port2: ethernet-port@2 {
 			reg = <2>;
 			label = "lan1";
 			phy-handle = <&switch0phy1>;
 		};
 
-		switch0port3: port@3 {
+		switch0port3: ethernet-port@3 {
 			reg = <3>;
 			label = "lan2";
 			phy-handle = <&switch0phy2>;
 		};
 
-		switch0port4: port@4 {
+		switch0port4: ethernet-port@4 {
 			reg = <4>;
 			label = "lan3";
 			phy-handle = <&switch0phy3>;
 		};
 
-		switch0port5: port@5 {
+		switch0port5: ethernet-port@5 {
 			reg = <5>;
 			label = "wan";
 			phy-handle = <&extphy>;
@@ -160,7 +160,7 @@
 	};
 
 	mdio {
-		switch0phy3: switch0phy3@14 {
+		switch0phy3: ethernet-phy@14 {
 			reg = <0x14>;
 		};
 	};

arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi

@@ -145,19 +145,17 @@
 };
 
 &mdio {
-	switch0: switch0@1 {
+	switch0: ethernet-switch@1 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <1>;
 
 		dsa,member = <0 0>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0port0: port@0 {
+			switch0port0: ethernet-port@0 {
 				reg = <0>;
 				label = "cpu";
 				ethernet = <&eth0>;
@@ -168,19 +166,19 @@
 				};
 			};
 
-			switch0port1: port@1 {
+			switch0port1: ethernet-port@1 {
 				reg = <1>;
 				label = "wan";
 				phy-handle = <&switch0phy0>;
 			};
 
-			switch0port2: port@2 {
+			switch0port2: ethernet-port@2 {
 				reg = <2>;
 				label = "lan0";
 				phy-handle = <&switch0phy1>;
 			};
 
-			switch0port3: port@3 {
+			switch0port3: ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 				phy-handle = <&switch0phy2>;
@@ -192,13 +190,13 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
 				reg = <0x11>;
 			};
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
 				reg = <0x12>;
 			};
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
 				reg = <0x13>;
 			};
 		};

arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts

@@ -152,31 +152,29 @@
 };
 
 &mdio {
-	switch0: switch0@1 {
+	switch0: ethernet-switch@1 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <1>;
 
 		dsa,member = <0 0>;
 
-		ports: ports {
+		ports: ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "cpu";
 				ethernet = <&eth0>;
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "wan";
 				phy-handle = <&switch0phy0>;
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan0";
 				phy-handle = <&switch0phy1>;
@@ -185,7 +183,7 @@
 				nvmem-cell-names = "mac-address";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 				phy-handle = <&switch0phy2>;
@@ -199,13 +197,13 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
 				reg = <0x11>;
 			};
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
 				reg = <0x12>;
 			};
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
 				reg = <0x13>;
 			};
 		};