---

yaml
---
r: 353428
b: refs/heads/master
c: b363bca
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: f4d8ada2a0d4634d6b334ec85328f04c2d01fc98
+refs/heads/master: b363bcaf1df2e8b6ab7c0dbfdc5bd8f275f08a96

trunk/Documentation/device-mapper/dm-raid.txt

@@ -141,3 +141,4 @@ Version History
 1.2.0	Handle creation of arrays that contain failed devices.
 1.3.0	Added support for RAID 10
 1.3.1	Allow device replacement/rebuild for RAID 10
+1.3.2   Fix/improve redundancy checking for RAID10

trunk/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -81,7 +81,8 @@ PA31	TXD4
 Required properties for pin configuration node:
 - atmel,pins: 4 integers array, represents a group of pins mux and config
   setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
-  The PERIPH 0 means gpio.
+  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
+  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
 
 Bits used for CONFIG:
 PULL_UP		(1 << 0): indicate this pin need a pull up.
@@ -126,7 +127,7 @@ pinctrl@fffff400 {
 		pinctrl_dbgu: dbgu-0 {
 			atmel,pins =
 				<1 14 0x1 0x0	/* PB14 periph A */
-				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
+				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
 		};
 	};
 };

trunk/Documentation/devicetree/bindings/sound/ak4642.txt

@@ -0,0 +1,17 @@
+AK4642 I2C transmitter
+
+This device supports I2C mode only.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648"
+  - reg : The chip select number on the I2C bus
+
+Example:
+
+&i2c {
+	ak4648: ak4648@0x12 {
+		compatible = "asahi-kasei,ak4642";
+		reg = <0x12>;
+	};
+};

trunk/Documentation/devicetree/bindings/sound/cs4271.txt

@@ -20,6 +20,18 @@ Optional properties:
 		!RESET pin
  - cirrus,amuteb-eq-bmutec:	When given, the Codec's AMUTEB=BMUTEC flag
 				is enabled.
+ - cirrus,enable-soft-reset:
+	The CS4271 requires its LRCLK and MCLK to be stable before its RESET
+	line is de-asserted. That also means that clocks cannot be changed
+	without putting the chip back into hardware reset, which also requires
+	a complete re-initialization of all registers.
+
+	One (undocumented) workaround is to assert and de-assert the PDN bit
+	in the MODE2 register. This workaround can be enabled with this DT
+	property.
+
+	Note that this is not needed in case the clocks are stable
+	throughout the entire runtime of the codec.
 
 Examples:
 

trunk/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt

@@ -0,0 +1,51 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm9712"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM9712's pins, and the jacks on the board:
+
+  WM9712 pins:
+
+  * MONOOUT
+  * HPOUTL
+  * HPOUTR
+  * LOUT2
+  * ROUT2
+  * OUT3
+  * LINEINL
+  * LINEINR
+  * PHONE
+  * PCBEEP
+  * MIC1
+  * MIC2
+  * Mic Bias
+
+  Board connectors:
+
+  * Headphone
+  * LineIn
+  * Mic
+
+- nvidia,ac97-controller : The phandle of the Tegra AC97 controller
+
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm9712-colibri_t20",
+		         "nvidia,tegra-audio-wm9712";
+	nvidia,model = "Toradex Colibri T20";
+
+	nvidia,audio-routing =
+		"Headphone", "HPOUTL",
+		"Headphone", "HPOUTR",
+		"LineIn", "LINEINL",
+		"LineIn", "LINEINR",
+		"Mic", "MIC1";
+
+	nvidia,ac97-controller = <&ac97>;
+};

trunk/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt

@@ -0,0 +1,22 @@
+NVIDIA Tegra 20 AC97 controller
+
+Required properties:
+- compatible : "nvidia,tegra20-ac97"
+- reg : Should contain AC97 controller registers location and length
+- interrupts : Should contain AC97 interrupt
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+  request selector for the AC97 controller
+- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO used to reset the external AC97 codec
+- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO corresponding with the AC97 DAP _FS line
+Example:
+
+ac97@70002000 {
+	compatible = "nvidia,tegra20-ac97";
+	reg = <0x70002000 0x200>;
+	interrupts = <0 81 0x04>;
+	nvidia,dma-request-selector = <&apbdma 12>;
+	nvidia,codec-reset-gpio = <&gpio 170 0>;
+	nvidia,codec-sync-gpio = <&gpio 120 0>;
+};

trunk/Documentation/devicetree/bindings/sound/renesas,fsi.txt

@@ -0,0 +1,26 @@
+Renesas FSI
+
+Required properties:
+- compatible			: "renesas,sh_fsi2" or "renesas,sh_fsi"
+- reg				: Should contain the register physical address and length
+- interrupts			: Should contain FSI interrupt
+
+- fsia,spdif-connection		: FSI is connected by S/PDFI
+- fsia,stream-mode-support	: FSI supports 16bit stream mode.
+- fsia,use-internal-clock	: FSI uses internal clock when master mode.
+
+- fsib,spdif-connection		: same as fsia
+- fsib,stream-mode-support	: same as fsia
+- fsib,use-internal-clock	: same as fsia
+
+Example:
+
+sh_fsi2: sh_fsi2@0xec230000 {
+	compatible = "renesas,sh_fsi2";
+	reg = <0xec230000 0x400>;
+	interrupts = <0 146 0x4>;
+
+	fsia,spdif-connection;
+	fsia,stream-mode-support;
+	fsia,use-internal-clock;
+};

trunk/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt

@@ -0,0 +1,14 @@
+Samsung SMDK audio complex
+
+Required properties:
+- compatible : "samsung,smdk-wm8994"
+- samsung,i2s-controller: The phandle of the Samsung I2S0 controller
+- samsung,audio-codec: The phandle of the WM8994 audio codec
+Example:
+
+sound {
+		compatible = "samsung,smdk-wm8994";
+
+		samsung,i2s-controller = <&i2s0>;
+		samsung,audio-codec = <&wm8994>;
+};

trunk/Documentation/devicetree/bindings/sound/samsung-i2s.txt

@@ -0,0 +1,63 @@
+* Samsung I2S controller
+
+Required SoC Specific Properties:
+
+- compatible : "samsung,i2s-v5"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- dmas: list of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+Optional SoC Specific Properties:
+
+- samsung,supports-6ch: If the I2S Primary sound source has 5.1 Channel
+  support, this flag is enabled.
+- samsung,supports-rstclr: This flag should be set if I2S software reset bit
+  control is required. When this flag is set I2S software reset bit will be
+  enabled or disabled based on need.
+- samsung,supports-secdai:If I2S block has a secondary FIFO and internal DMA,
+  then this flag is enabled.
+- samsung,idma-addr: Internal DMA register base address of the audio
+  sub system(used in secondary sound source).
+
+Required Board Specific Properties:
+
+- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK
+  interface lines. The format of the gpio specifier depends on the gpio
+  controller.
+  The syntax of samsung gpio specifier is
+	<[phandle of the gpio controller node]
+	 [pin number within the gpio controller]
+	 [mux function]
+	 [flags and pull up/down]
+	 [drive strength]>
+
+Example:
+
+- SoC Specific Portion:
+
+i2s@03830000 {
+	compatible = "samsung,i2s-v5";
+	reg = <0x03830000 0x100>;
+	dmas = <&pdma0 10
+		&pdma0 9
+		&pdma0 8>;
+	dma-names = "tx", "rx", "tx-sec";
+	samsung,supports-6ch;
+	samsung,supports-rstclr;
+	samsung,supports-secdai;
+	samsung,idma-addr = <0x03000000>;
+};
+
+- Board Specific Portion:
+
+i2s@03830000 {
+	gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */
+		<&gpz 1 2 0 0>, /* I2S_0_CDCLK */
+		<&gpz 2 2 0 0>, /* I2S_0_LRCK */
+		<&gpz 3 2 0 0>, /* I2S_0_SDI */
+		<&gpz 4 2 0 0>, /* I2S_0_SDO[1] */
+		<&gpz 5 2 0 0>, /* I2S_0_SDO[2] */
+		<&gpz 6 2 0 0>; /* I2S_0_SDO[3] */
+};

trunk/Documentation/devicetree/bindings/sound/tlv320aic3x.txt

@@ -11,6 +11,12 @@ Optional properties:
 
 - gpio-reset - gpio pin number used for codec reset
 - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
+- ai3x-micbias-vg - MicBias Voltage required.
+	1 - MICBIAS output is powered to 2.0V,
+	2 - MICBIAS output is powered to 2.5V,
+	3 - MICBIAS output is connected to AVDD,
+	If this node is not mentioned or if the value is incorrect, then MicBias
+	is powered down.
 
 Example:
 

trunk/Documentation/filesystems/f2fs.txt

@@ -175,9 +175,9 @@ consists of multiple segments as described below.
                                             align with the zone size <-|
                  |-> align with the segment size
      _________________________________________________________________________
-    |            |            |    Node     |   Segment   |   Segment  |      |
-    | Superblock | Checkpoint |   Address   |    Info.    |   Summary  | Main |
-    |    (SB)    |   (CP)     | Table (NAT) | Table (SIT) | Area (SSA) |      |
+    |            |            |   Segment   |    Node     |   Segment  |      |
+    | Superblock | Checkpoint |    Info.    |   Address   |   Summary  | Main |
+    |    (SB)    |   (CP)     | Table (SIT) | Table (NAT) | Area (SSA) |      |
     |____________|_____2______|______N______|______N______|______N_____|__N___|
                                                                        .      .
                                                              .                .
@@ -200,14 +200,14 @@ consists of multiple segments as described below.
  : It contains file system information, bitmaps for valid NAT/SIT sets, orphan
    inode lists, and summary entries of current active segments.
 
-- Node Address Table (NAT)
- : It is composed of a block address table for all the node blocks stored in
-   Main area.
-
 - Segment Information Table (SIT)
  : It contains segment information such as valid block count and bitmap for the
    validity of all the blocks.
 
+- Node Address Table (NAT)
+ : It is composed of a block address table for all the node blocks stored in
+   Main area.
+
 - Segment Summary Area (SSA)
  : It contains summary entries which contains the owner information of all the
    data and node blocks stored in Main area.
@@ -236,13 +236,13 @@ For file system consistency, each CP points to which NAT and SIT copies are
 valid, as shown as below.
 
   +--------+----------+---------+
-  |   CP   |    NAT   |   SIT   |
+  |   CP   |    SIT   |   NAT   |
   +--------+----------+---------+
   .         .          .          .
   .            .              .              .
   .               .                 .                 .
   +-------+-------+--------+--------+--------+--------+
-  | CP #0 | CP #1 | NAT #0 | NAT #1 | SIT #0 | SIT #1 |
+  | CP #0 | CP #1 | SIT #0 | SIT #1 | NAT #0 | NAT #1 |
   +-------+-------+--------+--------+--------+--------+
      |             ^                          ^
      |             |                          |

trunk/Documentation/kernel-parameters.txt

@@ -2438,7 +2438,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			real-time workloads.  It can also improve energy
 			efficiency for asymmetric multiprocessors.
 
-	rcu_nocbs_poll	[KNL,BOOT]
+	rcu_nocb_poll	[KNL,BOOT]
 			Rather than requiring that offloaded CPUs
 			(specified by rcu_nocbs= above) explicitly
 			awaken the corresponding "rcuoN" kthreads,

trunk/Documentation/x86/boot.txt

@@ -57,6 +57,10 @@ Protocol 2.10:	(Kernel 2.6.31) Added a protocol for relaxed alignment
 Protocol 2.11:	(Kernel 3.6) Added a field for offset of EFI handover
 		protocol entry point.
 
+Protocol 2.12:	(Kernel 3.8) Added the xloadflags field and extension fields
+	 	to struct boot_params for for loading bzImage and ramdisk
+		above 4G in 64bit.
+
 **** MEMORY LAYOUT
 
 The traditional memory map for the kernel loader, used for Image or
@@ -182,7 +186,7 @@ Offset	Proto	Name		Meaning
 0230/4	2.05+	kernel_alignment Physical addr alignment required for kernel
 0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
 0235/1	2.10+	min_alignment	Minimum alignment, as a power of two
-0236/2	N/A	pad3		Unused
+0236/2	2.12+	xloadflags	Boot protocol option flags
 0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
 023C/4	2.07+	hardware_subarch Hardware subarchitecture
 0240/8	2.07+	hardware_subarch_data Subarchitecture-specific data
@@ -582,6 +586,27 @@ Protocol:	2.10+
   misaligned kernel.  Therefore, a loader should typically try each
   power-of-two alignment from kernel_alignment down to this alignment.
 
+Field name:     xloadflags
+Type:           read
+Offset/size:    0x236/2
+Protocol:       2.12+
+
+  This field is a bitmask.
+
+  Bit 0 (read):	XLF_KERNEL_64
+	- If 1, this kernel has the legacy 64-bit entry point at 0x200.
+
+  Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G
+        - If 1, kernel/boot_params/cmdline/ramdisk can be above 4G.
+
+  Bit 2 (read):	XLF_EFI_HANDOVER_32
+	- If 1, the kernel supports the 32-bit EFI handoff entry point
+          given at handover_offset.
+
+  Bit 3 (read): XLF_EFI_HANDOVER_64
+	- If 1, the kernel supports the 64-bit EFI handoff entry point
+          given at handover_offset + 0x200.
+
 Field name:	cmdline_size
 Type:		read
 Offset/size:	0x238/4

trunk/Documentation/x86/zero-page.txt

@@ -19,6 +19,9 @@ Offset	Proto	Name		Meaning
 090/010	ALL	hd1_info	hd1 disk parameter, OBSOLETE!!
 0A0/010	ALL	sys_desc_table	System description table (struct sys_desc_table)
 0B0/010	ALL	olpc_ofw_header	OLPC's OpenFirmware CIF and friends
+0C0/004	ALL	ext_ramdisk_image ramdisk_image high 32bits
+0C4/004	ALL	ext_ramdisk_size  ramdisk_size high 32bits
+0C8/004	ALL	ext_cmd_line_ptr  cmd_line_ptr high 32bits
 140/080	ALL	edid_info	Video mode setup (struct edid_info)
 1C0/020	ALL	efi_info	EFI 32 information (struct efi_info)
 1E0/004	ALL	alk_mem_k	Alternative mem check, in KB
@@ -27,6 +30,7 @@ Offset	Proto	Name		Meaning
 1E9/001	ALL	eddbuf_entries	Number of entries in eddbuf (below)
 1EA/001	ALL	edd_mbr_sig_buf_entries	Number of entries in edd_mbr_sig_buffer
 				(below)
+1EF/001	ALL	sentinel	Used to detect broken bootloaders
 290/040	ALL	edd_mbr_sig_buffer EDD MBR signatures
 2D0/A00	ALL	e820_map	E820 memory map table
 				(array of struct e820entry)