---

yaml
---
r: 353427
b: refs/heads/master
c: f4d8ada
h: refs/heads/master
i:
  353425: 54c30b8
  353423: 186a3a1
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 315472d5abca4d4db90ba654fd616b9a694c80cf
+refs/heads/master: f4d8ada2a0d4634d6b334ec85328f04c2d01fc98

trunk/Documentation/device-mapper/dm-raid.txt

@@ -141,4 +141,3 @@ Version History
 1.2.0	Handle creation of arrays that contain failed devices.
 1.3.0	Added support for RAID 10
 1.3.1	Allow device replacement/rebuild for RAID 10
-1.3.2   Fix/improve redundancy checking for RAID10

trunk/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -81,8 +81,7 @@ PA31	TXD4
 Required properties for pin configuration node:
 - atmel,pins: 4 integers array, represents a group of pins mux and config
   setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
-  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
-  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
+  The PERIPH 0 means gpio.
 
 Bits used for CONFIG:
 PULL_UP		(1 << 0): indicate this pin need a pull up.
@@ -127,7 +126,7 @@ pinctrl@fffff400 {
 		pinctrl_dbgu: dbgu-0 {
 			atmel,pins =
 				<1 14 0x1 0x0	/* PB14 periph A */
-				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
+				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
 		};
 	};
 };

trunk/Documentation/devicetree/bindings/sound/cs4271.txt

@@ -20,18 +20,6 @@ Optional properties:
 		!RESET pin
  - cirrus,amuteb-eq-bmutec:	When given, the Codec's AMUTEB=BMUTEC flag
 				is enabled.
- - cirrus,enable-soft-reset:
-	The CS4271 requires its LRCLK and MCLK to be stable before its RESET
-	line is de-asserted. That also means that clocks cannot be changed
-	without putting the chip back into hardware reset, which also requires
-	a complete re-initialization of all registers.
-
-	One (undocumented) workaround is to assert and de-assert the PDN bit
-	in the MODE2 register. This workaround can be enabled with this DT
-	property.
-
-	Note that this is not needed in case the clocks are stable
-	throughout the entire runtime of the codec.
 
 Examples:
 

trunk/Documentation/devicetree/bindings/sound/tlv320aic3x.txt

@@ -11,12 +11,6 @@ Optional properties:
 
 - gpio-reset - gpio pin number used for codec reset
 - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
-- ai3x-micbias-vg - MicBias Voltage required.
-	1 - MICBIAS output is powered to 2.0V,
-	2 - MICBIAS output is powered to 2.5V,
-	3 - MICBIAS output is connected to AVDD,
-	If this node is not mentioned or if the value is incorrect, then MicBias
-	is powered down.
 
 Example:
 

trunk/Documentation/filesystems/f2fs.txt

@@ -175,9 +175,9 @@ consists of multiple segments as described below.
                                             align with the zone size <-|
                  |-> align with the segment size
      _________________________________________________________________________
-    |            |            |   Segment   |    Node     |   Segment  |      |
-    | Superblock | Checkpoint |    Info.    |   Address   |   Summary  | Main |
-    |    (SB)    |   (CP)     | Table (SIT) | Table (NAT) | Area (SSA) |      |
+    |            |            |    Node     |   Segment   |   Segment  |      |
+    | Superblock | Checkpoint |   Address   |    Info.    |   Summary  | Main |
+    |    (SB)    |   (CP)     | Table (NAT) | Table (SIT) | Area (SSA) |      |
     |____________|_____2______|______N______|______N______|______N_____|__N___|
                                                                        .      .
                                                              .                .
@@ -200,14 +200,14 @@ consists of multiple segments as described below.
  : It contains file system information, bitmaps for valid NAT/SIT sets, orphan
    inode lists, and summary entries of current active segments.
 
-- Segment Information Table (SIT)
- : It contains segment information such as valid block count and bitmap for the
-   validity of all the blocks.
-
 - Node Address Table (NAT)
  : It is composed of a block address table for all the node blocks stored in
    Main area.
 
+- Segment Information Table (SIT)
+ : It contains segment information such as valid block count and bitmap for the
+   validity of all the blocks.
+
 - Segment Summary Area (SSA)
  : It contains summary entries which contains the owner information of all the
    data and node blocks stored in Main area.
@@ -236,13 +236,13 @@ For file system consistency, each CP points to which NAT and SIT copies are
 valid, as shown as below.
 
   +--------+----------+---------+
-  |   CP   |    SIT   |   NAT   |
+  |   CP   |    NAT   |   SIT   |
   +--------+----------+---------+
   .         .          .          .
   .            .              .              .
   .               .                 .                 .
   +-------+-------+--------+--------+--------+--------+
-  | CP #0 | CP #1 | SIT #0 | SIT #1 | NAT #0 | NAT #1 |
+  | CP #0 | CP #1 | NAT #0 | NAT #1 | SIT #0 | SIT #1 |
   +-------+-------+--------+--------+--------+--------+
      |             ^                          ^
      |             |                          |

trunk/Documentation/kernel-parameters.txt

@@ -2438,7 +2438,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			real-time workloads.  It can also improve energy
 			efficiency for asymmetric multiprocessors.
 
-	rcu_nocb_poll	[KNL,BOOT]
+	rcu_nocbs_poll	[KNL,BOOT]
 			Rather than requiring that offloaded CPUs
 			(specified by rcu_nocbs= above) explicitly
 			awaken the corresponding "rcuoN" kthreads,

trunk/Documentation/x86/boot.txt

@@ -57,10 +57,6 @@ Protocol 2.10:	(Kernel 2.6.31) Added a protocol for relaxed alignment
 Protocol 2.11:	(Kernel 3.6) Added a field for offset of EFI handover
 		protocol entry point.
 
-Protocol 2.12:	(Kernel 3.8) Added the xloadflags field and extension fields
-	 	to struct boot_params for for loading bzImage and ramdisk
-		above 4G in 64bit.
-
 **** MEMORY LAYOUT
 
 The traditional memory map for the kernel loader, used for Image or
@@ -186,7 +182,7 @@ Offset	Proto	Name		Meaning
 0230/4	2.05+	kernel_alignment Physical addr alignment required for kernel
 0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
 0235/1	2.10+	min_alignment	Minimum alignment, as a power of two
-0236/2	2.12+	xloadflags	Boot protocol option flags
+0236/2	N/A	pad3		Unused
 0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
 023C/4	2.07+	hardware_subarch Hardware subarchitecture
 0240/8	2.07+	hardware_subarch_data Subarchitecture-specific data
@@ -586,27 +582,6 @@ Protocol:	2.10+
   misaligned kernel.  Therefore, a loader should typically try each
   power-of-two alignment from kernel_alignment down to this alignment.
 
-Field name:     xloadflags
-Type:           read
-Offset/size:    0x236/2
-Protocol:       2.12+
-
-  This field is a bitmask.
-
-  Bit 0 (read):	XLF_KERNEL_64
-	- If 1, this kernel has the legacy 64-bit entry point at 0x200.
-
-  Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G
-        - If 1, kernel/boot_params/cmdline/ramdisk can be above 4G.
-
-  Bit 2 (read):	XLF_EFI_HANDOVER_32
-	- If 1, the kernel supports the 32-bit EFI handoff entry point
-          given at handover_offset.
-
-  Bit 3 (read): XLF_EFI_HANDOVER_64
-	- If 1, the kernel supports the 64-bit EFI handoff entry point
-          given at handover_offset + 0x200.
-
 Field name:	cmdline_size
 Type:		read
 Offset/size:	0x238/4

trunk/Documentation/x86/zero-page.txt

@@ -19,9 +19,6 @@ Offset	Proto	Name		Meaning
 090/010	ALL	hd1_info	hd1 disk parameter, OBSOLETE!!
 0A0/010	ALL	sys_desc_table	System description table (struct sys_desc_table)
 0B0/010	ALL	olpc_ofw_header	OLPC's OpenFirmware CIF and friends
-0C0/004	ALL	ext_ramdisk_image ramdisk_image high 32bits
-0C4/004	ALL	ext_ramdisk_size  ramdisk_size high 32bits
-0C8/004	ALL	ext_cmd_line_ptr  cmd_line_ptr high 32bits
 140/080	ALL	edid_info	Video mode setup (struct edid_info)
 1C0/020	ALL	efi_info	EFI 32 information (struct efi_info)
 1E0/004	ALL	alk_mem_k	Alternative mem check, in KB
@@ -30,7 +27,6 @@ Offset	Proto	Name		Meaning
 1E9/001	ALL	eddbuf_entries	Number of entries in eddbuf (below)
 1EA/001	ALL	edd_mbr_sig_buf_entries	Number of entries in edd_mbr_sig_buffer
 				(below)
-1EF/001	ALL	sentinel	Used to detect broken bootloaders
 290/040	ALL	edd_mbr_sig_buffer EDD MBR signatures
 2D0/A00	ALL	e820_map	E820 memory map table
 				(array of struct e820entry)