---

yaml
---
r: 374009
b: refs/heads/master
c: 5852264
h: refs/heads/master
i:
  374007: 5c4e36b
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 35db05bb9d8818b33e1e206de70c3741580bf35a
+refs/heads/master: 5852264f9d6139751796853fdfca9d5230cbfb97

trunk/Documentation/clk.txt

@@ -174,9 +174,9 @@ int clk_foo_enable(struct clk_hw *hw)
 };
 
 Below is a matrix detailing which clk_ops are mandatory based upon the
-hardware capabilities of that clock.  A cell marked as "y" means
+hardware capbilities of that clock.  A cell marked as "y" means
 mandatory, a cell marked as "n" implies that either including that
-callback is invalid or otherwise unnecessary.  Empty cells are either
+callback is invalid or otherwise uneccesary.  Empty cells are either
 optional or must be evaluated on a case-by-case basis.
 
                            clock hardware characteristics

trunk/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt

@@ -1,84 +1,19 @@
 NVIDIA Tegra Power Management Controller (PMC)
 
-The PMC block interacts with an external Power Management Unit. The PMC
-mostly controls the entry and exit of the system from different sleep
-modes. It provides power-gating controllers for SoC and CPU power-islands.
-
-Required properties:
+Properties:
 - name : Should be pmc
 - compatible : Should contain "nvidia,tegra<chip>-pmc".
 - reg : Offset and length of the register set for the device
-- clocks : Must contain an entry for each entry in clock-names.
-- clock-names : Must include the following entries:
-  "pclk" (The Tegra clock of that name),
-  "clk32k_in" (The 32KHz clock input to Tegra).
-
-Optional properties:
 - nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
   The PMU is an external Power Management Unit, whose interrupt output
   signal is fed into the PMC. This signal is optionally inverted, and then
   fed into the ARM GIC. The PMC is not involved in the detection or
   handling of this interrupt signal, merely its inversion.
-- nvidia,suspend-mode : The suspend mode that the platform should use.
-  Valid values are 0, 1 and 2:
-  0 (LP0): CPU + Core voltage off and DRAM in self-refresh
-  1 (LP1): CPU voltage off and DRAM in self-refresh
-  2 (LP2): CPU voltage off
-- nvidia,core-power-req-active-high : Boolean, core power request active-high
-- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high
-- nvidia,combined-power-req : Boolean, combined power request for CPU & Core
-- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC)
-			   is enabled.
-
-Required properties when nvidia,suspend-mode is specified:
-- nvidia,cpu-pwr-good-time : CPU power good time in uS.
-- nvidia,cpu-pwr-off-time : CPU power off time in uS.
-- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time>
-			      Core power good time in uS.
-- nvidia,core-pwr-off-time : Core power off time in uS.
-
-Required properties when nvidia,suspend-mode=<0>:
-- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector
-  The LP0 vector contains the warm boot code that is executed by AVP when
-  resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7
-  processor and always being the first boot processor when chip is power on
-  or resume from deep sleep mode. When the system is resumed from the deep
-  sleep mode, the warm boot code will restore some PLLs, clocks and then
-  bring up CPU0 for resuming the system.
 
 Example:
 
-/ SoC dts including file
 pmc@7000f400 {
 	compatible = "nvidia,tegra20-pmc";
 	reg = <0x7000e400 0x400>;
-	clocks = <&tegra_car 110>, <&clk32k_in>;
-	clock-names = "pclk", "clk32k_in";
 	nvidia,invert-interrupt;
-	nvidia,suspend-mode = <1>;
-	nvidia,cpu-pwr-good-time = <2000>;
-	nvidia,cpu-pwr-off-time = <100>;
-	nvidia,core-pwr-good-time = <3845 3845>;
-	nvidia,core-pwr-off-time = <458>;
-	nvidia,core-power-req-active-high;
-	nvidia,sys-clock-req-active-high;
-	nvidia,lp0-vec = <0xbdffd000 0x2000>;
-};
-
-/ Tegra board dts file
-{
-	...
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock {
-			compatible = "fixed-clock";
-			reg=<0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
-	...
 };