Merge branches 'pci/host-designware', 'pci/host-imx6', 'pci/host-mveb…

…u' and 'pci/host-tegra' into next

* pci/host-designware:
  PCI: designware: Remove unnecessary use of 'conf_lock' spinlock
  PCI: designware: Use new OF interrupt mapping when possible
  PCI: designware: Fix iATU programming for cfg1, io and mem viewport
  PCI: designware: Fix comment for setting number of lanes

* pci/host-imx6:
  PCI: designware: Split Exynos and i.MX bindings

* pci/host-mvebu:
  PCI: mvebu: Use '%pa' for printing 'phys_addr_t' type
  PCI: mvebu: Remove unnecessary use of 'conf_lock' spinlock
  PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
  bus: mvebu-mbus: allow several windows with the same target/attribute
  bus: mvebu-mbus: Avoid setting an undefined window size
  PCI: mvebu: fix off-by-one in the computed size of the mbus windows

* pci/host-tegra:
  PCI: tegra: Use new OF interrupt mapping when possible

Documentation/devicetree/bindings/pci/designware-pcie.txt

@@ -1,15 +1,7 @@
 * Synopsys Designware PCIe interface
 
 Required properties:
-- compatible: should contain "snps,dw-pcie" to identify the
-	core, plus an identifier for the specific instance, such
-	as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie".
-- reg: base addresses and lengths of the pcie controller,
-	the phy controller, additional register for the phy controller.
-- interrupts: interrupt values for level interrupt,
-	pulse interrupt, special interrupt.
-- clocks: from common clock binding: handle to pci clock.
-- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
+- compatible: should contain "snps,dw-pcie" to identify the core.
 - #address-cells: set to <3>
 - #size-cells: set to <2>
 - device_type: set to "pci"
@@ -19,65 +11,11 @@ Required properties:
 	to define the mapping of the PCIe interface to interrupt
 	numbers.
 - num-lanes: number of lanes to use
+- clocks: Must contain an entry for each entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+	- "pcie"
+	- "pcie_bus"
 
 Optional properties:
 - reset-gpio: gpio pin number of power good signal
-
-Optional properties for fsl,imx6q-pcie
-- power-on-gpio: gpio pin number of power-enable signal
-- wake-up-gpio: gpio pin number of incoming wakeup signal
-- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
-
-Example:
-
-SoC specific DT Entry:
-
-	pcie@290000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x290000 0x1000
-			0x270000 0x1000
-			0x271000 0x40>;
-		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
-		clocks = <&clock 28>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 53>;
-		num-lanes = <4>;
-	};
-
-	pcie@2a0000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x2a0000 0x1000
-			0x272000 0x1000
-			0x271040 0x40>;
-		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
-		clocks = <&clock 29>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 56>;
-		num-lanes = <4>;
-	};
-
-Board specific DT Entry:
-
-	pcie@290000 {
-		reset-gpio = <&pin_ctrl 5 0>;
-	};
-
-	pcie@2a0000 {
-		reset-gpio = <&pin_ctrl 22 0>;
-	};

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt

@@ -0,0 +1,38 @@
+* Freescale i.MX6 PCIe interface
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: "fsl,imx6q-pcie"
+- reg: base addresse and length of the pcie controller
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+	- "msi": The interrupt that is asserted when an MSI is received
+- clock-names: Must include the following additional entries:
+	- "pcie_phy"
+
+Example:
+
+	pcie@0x01000000 {
+		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+		reg = <0x01ffc000 0x4000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
+			  0x81000000 0 0          0x01f80000 0 0x00010000
+			  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
+		num-lanes = <1>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks 144>, <&clks 206>, <&clks 189>;
+		clock-names = "pcie", "pcie_bus", "pcie_phy";
+	};

Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt

@@ -0,0 +1,65 @@
+* Samsung Exynos 5440 PCIe interface
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: "samsung,exynos5440-pcie"
+- reg: base addresses and lengths of the pcie controller,
+	the phy controller, additional register for the phy controller.
+- interrupts: A list of interrupt outputs for level interrupt,
+	pulse interrupt, special interrupt.
+
+Example:
+
+SoC specific DT Entry:
+
+	pcie@290000 {
+		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
+		reg = <0x290000 0x1000
+			0x270000 0x1000
+			0x271000 0x40>;
+		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
+		clocks = <&clock 28>, <&clock 27>;
+		clock-names = "pcie", "pcie_bus";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
+			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <4>;
+	};
+
+	pcie@2a0000 {
+		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
+		reg = <0x2a0000 0x1000
+			0x272000 0x1000
+			0x271040 0x40>;
+		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
+		clocks = <&clock 29>, <&clock 27>;
+		clock-names = "pcie", "pcie_bus";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
+			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <4>;
+	};
+
+Board specific DT Entry:
+
+	pcie@290000 {
+		reset-gpio = <&pin_ctrl 5 0>;
+	};
+
+	pcie@2a0000 {
+		reset-gpio = <&pin_ctrl 22 0>;
+	};

drivers/bus/mvebu-mbus.c

@@ -56,6 +56,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/debugfs.h>
+#include <linux/log2.h>
 
 /*
  * DDR target is the same on all platforms.
@@ -222,12 +223,6 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
 		 */
 		if ((u64)base < wend && end > wbase)
 			return 0;
-
-		/*
-		 * Check if target/attribute conflicts
-		 */
-		if (target == wtarget && attr == wattr)
-			return 0;
 	}
 
 	return 1;
@@ -266,6 +261,17 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
 		mbus->soc->win_cfg_offset(win);
 	u32 ctrl, remap_addr;
 
+	if (!is_power_of_2(size)) {
+		WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+		return -EINVAL;
+	}
+
+	if ((base & (phys_addr_t)(size - 1)) != 0) {
+		WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+		     size);
+		return -EINVAL;
+	}
+
 	ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
 		(attr << WIN_CTRL_ATTR_SHIFT)    |
 		(target << WIN_CTRL_TGT_SHIFT)   |
@@ -413,6 +419,10 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
 			   win, (unsigned long long)wbase,
 			   (unsigned long long)(wbase + wsize), wtarget, wattr);
 
+		if (!is_power_of_2(wsize) ||
+		    ((wbase & (u64)(wsize - 1)) != 0))
+			seq_puts(seq, " (Invalid base/size!!)");
+
 		if (win < mbus->soc->num_remappable_wins) {
 			seq_printf(seq, " (remap %016llx)\n",
 				   (unsigned long long)wremap);

drivers/pci/host/pci-exynos.c

@@ -545,7 +545,6 @@ static int __init add_pcie_port(struct pcie_port *pp,
 	pp->root_bus_nr = -1;
 	pp->ops = &exynos_pcie_host_ops;
 
-	spin_lock_init(&pp->conf_lock);
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to initialize host\n");

drivers/pci/host/pci-imx6.c

@@ -507,7 +507,6 @@ static int __init imx6_add_pcie_port(struct pcie_port *pp,
 	pp->root_bus_nr = -1;
 	pp->ops = &imx6_pcie_host_ops;
 
-	spin_lock_init(&pp->conf_lock);
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to initialize host\n");