Merge tag 'fixes-for-v4.15-rc4' of git://git.kernel.org/pub/scm/linux…

…/kernel/git/balbi/usb into usb-linus Felipe writes: usb: fixes for v4.15-rc4 We have a few fixes on dwc3: - one fix which only happens with some implementations where we need to wait longer for some commands to finish. - Another fix for high-bandwidth isochronous endpoint programming making sure that we send the correct DATA tokens in the correct sequence - A couple PM fixes on dwc3-of-simple The other synopsys controller driver (dwc2) got a fix for FIFO size programming. Other than these, we have a couple Kconfig fixes making sure that dependencies are properly setup.
mariux64 · Dec 12, 2017 · c1ed473 · c1ed473
2 parents 72b663a + 9dbe416
commit c1ed473
Show file tree

Hide file tree

Showing 844 changed files with 7,687 additions and 5,067 deletions.
diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/arm/ccn.txt
@@ -15,7 +15,7 @@ Required properties:
 
 Example:
 
-	ccn@0x2000000000 {
+	ccn@2000000000 {
 		compatible = "arm,ccn-504";
 		reg = <0x20 0x00000000 0 0x1000000>;
 		interrupts = <0 181 4>;

diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
@@ -49,7 +49,7 @@ An interrupt consumer on an SoC using crossbar will use:
 	interrupts = <GIC_SPI request_number interrupt_level>
 
 Example:
-	device_x@0x4a023000 {
+	device_x@4a023000 {
 		/* Crossbar 8 used */
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 		...

diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt
@@ -8,7 +8,7 @@ Required properties:
 - interrupts : Should contain MC General interrupt.
 
 Example:
-	memory-controller@0x7000f000 {
+	memory-controller@7000f000 {
 		compatible = "nvidia,tegra20-mc";
 		reg = <0x7000f000 0x024
 		       0x7000f03c 0x3c4>;

diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt
@@ -17,7 +17,7 @@ Optional properties:
 - clock-output-names : From common clock binding.
 
 Example:
-	clock@0xff000000 {
+	clock@ff000000 {
 		compatible = "adi,axi-clkgen";
 		#clock-cells = <0>;
 		reg = <0xff000000 0x1000>;

diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt
@@ -23,7 +23,7 @@ Example:
 		clocks = <&clk_osc>;
 	};
 
-	aux: aux@0x7e215004 {
+	aux: aux@7e215004 {
 		compatible = "brcm,bcm2835-aux";
 		#clock-cells = <1>;
 		reg = <0x7e215000 0x8>;

diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt
@@ -24,7 +24,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10030000 {
+	clock: clock-controller@10030000 {
 		compatible = "samsung,exynos4210-clock";
 		reg = <0x10030000 0x20000>;
 		#clock-cells = <1>;

diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt
@@ -22,7 +22,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5250-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt
@@ -30,7 +30,7 @@ Example 1: An example of a clock controller node is listed below.
 		#clock-cells = <0>;
 	};
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5410-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt
@@ -23,7 +23,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5420-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt
@@ -21,7 +21,7 @@ tree sources.
 
 Example: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5440-clock";
 		reg = <0x160000 0x10000>;
 		#clock-cells = <1>;

diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt
@@ -14,7 +14,7 @@ Required properties:
 
 Example:
 
-pllctrl: pll-controller@0x02310000 {
+pllctrl: pll-controller@02310000 {
 	compatible = "ti,keystone-pllctrl", "syscon";
 	reg = <0x02310000 0x200>;
 };
diff --git a/Documentation/devicetree/bindings/clock/zx296702-clk.txt b/Documentation/devicetree/bindings/clock/zx296702-clk.txt
@@ -20,13 +20,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h
 for the full list of zx296702 clock IDs.
 
 
-topclk: topcrm@0x09800000 {
+topclk: topcrm@09800000 {
         compatible = "zte,zx296702-topcrm-clk";
         reg = <0x09800000 0x1000>;
         #clock-cells = <1>;
 };
 
-uart0: serial@0x09405000 {
+uart0: serial@09405000 {
         compatible = "zte,zx296702-uart";
         reg = <0x09405000 0x1000>;
         interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;

diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt
@@ -456,7 +456,7 @@ System ON/OFF key driver
       Definition: this is phandle to the register map node.
 
 EXAMPLE:
-	snvs-pwrkey@0x020cc000 {
+	snvs-pwrkey@020cc000 {
 		compatible = "fsl,sec-v4.0-pwrkey";
 		regmap = <&snvs>;
 		interrupts = <0 4 0x4>
@@ -545,7 +545,7 @@ FULL EXAMPLE
 			interrupts = <93 2>;
 		};
 
-		snvs-pwrkey@0x020cc000 {
+		snvs-pwrkey@020cc000 {
 			compatible = "fsl,sec-v4.0-pwrkey";
 			regmap = <&sec_mon>;
 			interrupts = <0 4 0x4>;

diff --git a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt
@@ -9,7 +9,7 @@ Required properties:
 - clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon";
 
 Example:
-	dfi: dfi@0xff630000 {
+	dfi: dfi@ff630000 {
 		compatible = "rockchip,rk3399-dfi";
 		reg = <0x00 0xff630000 0x00 0x4000>;
 		rockchip,pmu = <&pmugrf>;

diff --git a/Documentation/devicetree/bindings/display/atmel,lcdc.txt b/Documentation/devicetree/bindings/display/atmel,lcdc.txt
@@ -27,7 +27,7 @@ Optional properties:
 
 Example:
 
-	fb0: fb@0x00500000 {
+	fb0: fb@00500000 {
 		compatible = "atmel,at91sam9g45-lcdc";
 		reg = <0x00500000 0x1000>;
 		interrupts = <23 3 0>;
@@ -41,7 +41,7 @@ Example:
 
 Example for fixed framebuffer memory:
 
-	fb0: fb@0x00500000 {
+	fb0: fb@00500000 {
 		compatible = "atmel,at91sam9263-lcdc";
 		reg = <0x00700000 0x1000 0x70000000 0x200000>;
 		[...]

diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt
@@ -73,7 +73,7 @@ Hypervisor OS configuration:
 		max-read-transactions = <31>;
 		channel-reset-timeout-cycles = <0x500>;
 
-		hidma_24: dma-controller@0x5c050000 {
+		hidma_24: dma-controller@5c050000 {
 			compatible = "qcom,hidma-1.0";
 			reg = <0 0x5c050000 0x0 0x1000>,
 			      <0 0x5c0b0000 0x0 0x1000>;
@@ -85,7 +85,7 @@ Hypervisor OS configuration:
 
 Guest OS configuration:
 
-	hidma_24: dma-controller@0x5c050000 {
+	hidma_24: dma-controller@5c050000 {
 		compatible = "qcom,hidma-1.0";
 		reg = <0 0x5c050000 0x0 0x1000>,
 		      <0 0x5c0b0000 0x0 0x1000>;

diff --git a/Documentation/devicetree/bindings/dma/zxdma.txt b/Documentation/devicetree/bindings/dma/zxdma.txt
@@ -13,7 +13,7 @@ Required properties:
 Example:
 
 Controller:
-	dma: dma-controller@0x09c00000{
+	dma: dma-controller@09c00000{
 		compatible = "zte,zx296702-dma";
 		reg = <0x09c00000 0x1000>;
 		clocks = <&topclk ZX296702_DMA_ACLK>;

diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt
@@ -1,7 +1,12 @@
 EEPROMs (SPI) compatible with Atmel at25.
 
 Required properties:
-- compatible : "atmel,at25".
+- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25".
+  Example "<vendor>,<type>" values:
+    "microchip,25lc040"
+    "st,m95m02"
+    "st,m95256"
+
 - reg : chip select number
 - spi-max-frequency : max spi frequency to use
 - pagesize : size of the eeprom page
@@ -13,7 +18,7 @@ Optional properties:
 - spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
 - read-only : this parameter-less property disables writes to the eeprom
 
-Obsolete legacy properties are can be used in place of "size", "pagesize",
+Obsolete legacy properties can be used in place of "size", "pagesize",
 "address-width", and "read-only":
 - at25,byte-len : total eeprom size in bytes
 - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
@@ -22,8 +27,8 @@ Obsolete legacy properties are can be used in place of "size", "pagesize",
 Additional compatible properties are also allowed.
 
 Example:
-	at25@0 {
-		compatible = "atmel,at25", "st,m95256";
+	eeprom@0 {
+		compatible = "st,m95256", "atmel,at25";
 		reg = <0>
 		spi-max-frequency = <5000000>;
 		spi-cpha;

diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
@@ -30,7 +30,7 @@ Optional properties:
 
 Example:
 
-gpio_altr: gpio@0xff200000 {
+gpio_altr: gpio@ff200000 {
 	compatible = "altr,pio-1.0";
 	reg = <0xff200000 0x10>;
 	interrupts = <0 45 4>;

diff --git a/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt
@@ -18,7 +18,7 @@ Optional properties:
 Example
 
 / {
-	i2c4: i2c4@0x10054000 {
+	i2c4: i2c4@10054000 {
 		compatible = "ingenic,jz4780-i2c";
 		reg = <0x10054000 0x1000>;
 

diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-hp03@0x77 {
+hp03@77 {
 	compatible = "hoperf,hp03";
 	reg = <0x77>;
 	xclr-gpio = <&portc 0 0x0>;

diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt
@@ -15,7 +15,7 @@ Optional properties:
 Example:
 
 	i2c@80110000 {
-		bu21013_tp@0x5c {
+		bu21013_tp@5c {
 			compatible = "rohm,bu21013_tp";
 			reg = <0x5c>;
 			touch-gpio = <&gpio2 20 0x4>;

diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
@@ -155,15 +155,15 @@ Example:
 		      <0x0 0xe112f000 0 0x02000>,
 		      <0x0 0xe1140000 0 0x10000>,
 		      <0x0 0xe1160000 0 0x10000>;
-		v2m0: v2m@0x8000 {
+		v2m0: v2m@8000 {
 			compatible = "arm,gic-v2m-frame";
 			msi-controller;
 			reg = <0x0 0x80000 0 0x1000>;
 		};
 
 		....
 
-		v2mN: v2m@0x9000 {
+		v2mN: v2m@9000 {
 			compatible = "arm,gic-v2m-frame";
 			msi-controller;
 			reg = <0x0 0x90000 0 0x1000>;

diff --git a/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt
@@ -71,7 +71,7 @@ Example 2:
 	 * An interrupt generating device that is wired to a Meta external
 	 * trigger block.
 	 */
-	uart1: uart@0x02004c00 {
+	uart1: uart@02004c00 {
 		// Interrupt source '5' that is level-sensitive.
 		// Note that there are only two cells as specified in the
 		// interrupt parent's '#interrupt-cells' property.

diff --git a/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt
@@ -51,7 +51,7 @@ Example 1:
 	/*
 	 * TZ1090 PDC block
 	 */
-	pdc: pdc@0x02006000 {
+	pdc: pdc@02006000 {
 		// This is an interrupt controller node.
 		interrupt-controller;
 

diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt b/Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt
@@ -39,7 +39,7 @@ Example:
 
 The following is an example from the SPEAr320 SoC dtsi file.
 
-shirq: interrupt-controller@0xb3000000 {
+shirq: interrupt-controller@b3000000 {
 	compatible = "st,spear320-shirq";
 	reg = <0xb3000000 0x1000>;
 	interrupts = <28 29 30 1>;

diff --git a/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt b/Documentation/devicetree/bindings/mailbox/altera-mailbox.txt
@@ -14,15 +14,15 @@ Optional properties:
 			depends on the interrupt controller parent.
 
 Example:
-	mbox_tx: mailbox@0x100 {
+	mbox_tx: mailbox@100 {
 		compatible = "altr,mailbox-1.0";
 		reg = <0x100 0x8>;
 		interrupt-parent = < &gic_0 >;
 		interrupts = <5>;
 		#mbox-cells = <1>;
 	};
 
-	mbox_rx: mailbox@0x200 {
+	mbox_rx: mailbox@200 {
 		compatible = "altr,mailbox-1.0";
 		reg = <0x200 0x8>;
 		interrupt-parent = < &gic_0 >;
@@ -40,7 +40,7 @@ support only one channel).The equivalent "mbox-names" property value can be
 used to give a name to the communication channel to be used by the client user.
 
 Example:
-	mclient0: mclient0@0x400 {
+	mclient0: mclient0@400 {
 		compatible = "client-1.0";
 		reg = <0x400 0x10>;
 		mbox-names = "mbox-tx", "mbox-rx";

diff --git a/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt
@@ -15,7 +15,7 @@ Optional properties:
 - brcm,use-bcm-hdr:  present if a BCM header precedes each frame.
 
 Example:
-	pdc0: iproc-pdc0@0x612c0000 {
+	pdc0: iproc-pdc0@612c0000 {
 		compatible = "brcm,iproc-pdc-mbox";
 		reg = <0 0x612c0000 0 0x445>;  /* PDC FS0 regs */
 		interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;

diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt
@@ -17,7 +17,7 @@ Optional properties:
 
 Example:
 
-gsc_0:  gsc@0x13e00000 {
+gsc_0:  gsc@13e00000 {
 	compatible = "samsung,exynos5250-gsc";
 	reg = <0x13e00000 0x1000>;
 	interrupts = <0 85 0>;

diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt
@@ -68,7 +68,7 @@ vcodec_dec: vcodec@16000000 {
                   "vdec_bus_clk_src";
   };
 
-  vcodec_enc: vcodec@0x18002000 {
+  vcodec_enc: vcodec@18002000 {
     compatible = "mediatek,mt8173-vcodec-enc";
     reg = <0 0x18002000 0 0x1000>,    /*VENC_SYS*/
           <0 0x19002000 0 0x1000>;    /*VENC_LT_SYS*/

diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt
@@ -44,7 +44,7 @@ Device node example
 	       vin0 = &vin0;
 	};
 
-        vin0: vin@0xe6ef0000 {
+        vin0: vin@e6ef0000 {
                 compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin";
                 clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
                 reg = <0 0xe6ef0000 0 0x1000>;

diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt
@@ -138,7 +138,7 @@ Example:
 		};
 
 		/* MIPI CSI-2 bus IF sensor */
-		s5c73m3: sensor@0x1a {
+		s5c73m3: sensor@1a {
 			compatible = "samsung,s5c73m3";
 			reg = <0x1a>;
 			vddio-supply = <...>;

diff --git a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt
@@ -8,7 +8,7 @@ Bindings, specific for the sh_mobile_ceu_camera.c driver:
 
 Example:
 
-ceu0: ceu@0xfe910000 {
+ceu0: ceu@fe910000 {
 	compatible = "renesas,sh-mobile-ceu";
 	reg = <0xfe910000 0xa0>;
 	interrupt-parent = <&intcs>;